SwissTech Heavy Duty Stub Drills HSS-Co Cobalt

Heavy duty drill made of high quality cobalt material with excellent heat resistance. For drilling steels up to 1,400N/mm2, stainless steel, heat resistant steels and bronze. Ideally suited for volume production on automatics. Point angle: 135. Helix angle: Normal. Web thickness: Strengthened. Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to DIN1897RN.

Series 2010

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Gauge Sizes

Dormer Jobber Drills Solid Carbide

General-purpose carbide drills. 120 four-facet point for accurate centering and improved hole quality. Bright finish.

Series R100 - Metric

Sherwood Extra Length Drills Steam Tempered HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328 : Part 1 : 1986.

For all dimensional specifications please refer to our catalogue.

Series E100 - Inch Sizes

Dormer Stub Drills

A921
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow. Alcrona Top coating for extended tool life
Size Range: 2.5-16.0mm. Manufactured to BS 323, DIN1897, ansi.

A921 HSCO Stub Drills

A9210
Excellent for: Carbon/alloy steels, stainless and cast iron
Good for: Titanium, nickel and copper

Sherwood® Solid Carbide Drills

Sherwood Solid Carbide Stub Drills are suitable for drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic.
Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6.
Manufactured to Works Standard.

Solid Carbide Stub Drills

Sherwood Extra Length Drills Taper Shank HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle 8-20, tolerance of diameter: h8. Point angle to BS328 PTI 1986.

For all dimensional specifications please refer to our catalogue.

2 Morse Taper -Metric

Sherwood Stub Drills HSS

General-purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118, Helix angle: Normal, Web thickness: standard, Relief angle: 10-20, Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to BS328:Part 1:1986/DIN338.

Series S100

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100

Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Metric