Dormer HSCO Jobber Drills

A941 (10xD) - 1.0-16.0mm, 3/64-5/8 Inch

A941 Long Series HSCO Jobber Drills Coated

A941
Excellent for: Carbon/alloy steels, stainless, cast iron and aluminium
Good for: Titanium and copper

Guhring Production Jobber Drills HSS-Co 5%

Rigid, high-heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. Limited suitability for special alloys such as hastaloy, inconel, nimonic etc. Manufactured to DIN338.

Series 605 - Inch

SwissTech Jobber Drills HSS TiN Coated

General-purpose drill, to drill steels with a tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. TiN coating provides longer tool life. Point angle: 118. Helix angle: Normal. Web thickness: Normal. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufactured to DIN338RN.

Series 1001

Sherwood® Printed Circuit Board Drills Solid Carbide

Suitable for drilling through printed circuit boards. Shank diameter: 3.175mm, 38mm overall length. Manufactured to DIN1899.

For all dimensional and technical specifications please refer to our catalogue.

Guhring Production Jobber Drills HSS-Co 5%

Solid Carbide Jobber drills are especially suitable for drilling cast steels, grey cast iron, chilled cast iron, austenitic manganese steels, bronzes, light metals and non-ferrous metals. Furthermore suitable for the economic machining of abrasive materials (AlSi-alloys), fibre-reinforced plastics and other Duroplastics liable to cause severe abrasion on cutting lips and lands.

Series 5517 - Metric

Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Metric

Guhring Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series 205

HSS-Co 5% Production Jobber Drills

For multiple machining tasks. Suitable for non-ferrous metals, structural steels and carbon steels, high-alloyed steels, cast iron and cast alloys, plastics as well as aluminium.
Manufactured to BS 328, DIN338RN.

Series 5523

Dormer Stub Drills

A920 - HSCo PFX Stub Drills
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow.Size Range: 1.0-20.0mm. Manufactured to BS 323, DIN1897, ansi.

A920 - HSCo PFX Stub Drills - Inch

Sherwood Extra Length Drills Taper Shank HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle 8-20, tolerance of diameter: h8. Point angle to BS328 PTI 1986.

For all dimensional specifications please refer to our catalogue.

1 Morse Taper - Metric