SwissTech Heavy Duty Jobber Drills HSS-Co 8% Cobalt

The addition of up to 8% Cobalt allows higher speeds to be used without reducing the life of the tool, increasing productivity. 28 Helix and 135 Point. Manufactured to DIN338RN. Point to DIN1412C.

Series 1020 - Metric

Sherwood Long Series Drills HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328:Part 1:1986, DIN340RN, ISO494. Bright finish; drills are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

Bright finish.

Walter Titex Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A1211

Dormer Stub Drills

The A120 HSS stub drill from Dormer has a standard helix right hand spiral. The rigidity of these Dormer stub drill bits allow them to be used in portable drills, turret and automatic lathes.

Series A120 Stub Drill HSS - Metric

Sherwood Long Series Drills Steam Tempered HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

Sherwood Drill Blanks HSS

Jobber length blank hardened and ground all over. Accurately ground without back taper. Diameter Tolerance: h8. Manufactured to DIN 338.

Series J400

Dormer HSCO Jobber Drills

A900 Multi Application HSCo Jobber Drills Bright.
High productivity one-hit drilling across a wide range of materials.
130° special point geometry ensures consistent hole size and quality throughout the full depth of the hole.
Size Range: A900 (6xD) - 1.0-20.0mm, 3/64-25/32 Inch.

Guhring GT100 Jobber Drills HSS

HSS GT100 jobber drills. For drilling in difficult conditions when swarf congestion prevents an adequate flow of coolant. For use in steel and cast iron having a hardness of up to 1000N/mm2. Not recommended for nickel-chrome steels or similar material. Manufactured to BS 328/DIN 338.

Series 549 - Metric

Guhring Stub Drills Carbide SL

Carbide drills deliver a quantum leap in high speed holemaking performance and tool life that manufacturers have been asking for. Carbide tooling provides faster cutting rates, longer tool life, better positional and dimensional accuracy and improved surface finish. Short cycle times and tighter tolerances translate into maximum machine utilizations, better part quality and optimum holemaking cost savings.

Series 5516

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100