Sherwood Jobber Drills Bright Finish HSS

General-purpose drills for steel, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328/DIN338RN. Bright finish: drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.

Series J100 - Metric - Bright Finish

Dormer Solid Carbide Drills

The new Dormer MP-X range of multi-application carbide drills are cost effective, high performance drills that offer high productivity and supreme value for money. A wide range of materials can be machined using a minimum number of drills, to reduce stock-holding and associated costs.

MP-X Solid Carbide Drills

Dormer MP-X solid carbide drills deliver the following benefits and features:

Benefits
? Exceptional value with no compromise on quality.
? High productivity.
? Excellent hole quality.
? Availability.
? Reduced tooling costs.

Material
Micro-grain carbide for an excellent combination of hardness and toughness, resulting in high wear resistance and longer tool life.

Coating
Multi-layer titanium aluminum nitride (TiAlN) coating gives:
? Improved stability of cutting edges.
? Outstanding wear protection.
? High hardness properties.
? High toughness and oxidation stability
? Longer tool life and higher productivity.

Flute Geometry
Strong web design gives excellent crosssectional strength and facilitates chip evacuation.

Point Geometry
140 point angle with good centring capabilities and low thrust force design, suited to multiapplication drilling.

Multi-Application
Multi-application drilling across a wide range of materials, including:
? Carbon and alloy steels.
? Stainless steels.
? Cast iron.
? Aluminium.
? Magnesium alloys.
? Copper.

Suitable for Regrinding
The quality of design will allow consistently high levels of performance and tool life after the product is reconditioned, providing further cost reduction benefits.

Sherwood Drill Blanks HSS

Jobber length blank hardened and ground all over. Accurately ground without back taper. Diameter Tolerance: h8. Manufactured to DIN 338.

Series J400

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Gauge Sizes

Sherwood Extra Length Drills Steam Tempered HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328 : Part 1 : 1986.

For all dimensional specifications please refer to our catalogue.

Series E100 - Inch Sizes

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100

Dormer Carbide Stub Drills

R120 - Carbide Stub Drill
For general carbide drilling applications.
120° four-facet point for improved accuracy & hole quality.
Bright Finish. Size Range: 1.0-12.0mm. Manufactured to BS 323, DIN6539.

SwissTech Heavy Duty Jobber Drills HSS-Co 8% Cobalt

The addition of up to 8% Cobalt allows higher speeds to be used without reducing the life of the tool, increasing productivity. 28 Helix and 135 Point. Manufactured to DIN338RN. Point to DIN1412C.

Series 1020 - Metric

HSS-Co 5% Production Jobber Drills

For multiple machining tasks. Suitable for non-ferrous metals, structural steels and carbon steels, high-alloyed steels, cast iron and cast alloys, plastics as well as aluminium.
Manufactured to BS 328, DIN338RN.

Series 5523

Dormer Stub Drills

A920 - HSCo PFX Stub Drills
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow.Size Range: 1.0-20.0mm. Manufactured to BS 323, DIN1897, ansi.

A920 - HSCo PFX Stub Drills - metric