SwissTech Jobber Drills HSS TiN Coated

General-purpose drill, to drill steels with a tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. TiN coating provides longer tool life. Point angle: 118. Helix angle: Normal. Web thickness: Normal. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufactured to DIN338RN.

Series 1001

SwissTech High Helix Drills for Stainless Steel HSS-Co 8% TiN Coated

Heavy-duty drill for stainless steel, heat and acid-resistant steels, short chipping and high strength steels. High heat resistance allows drilling in titanium and titanium alloys. TiN coating provides longer tool life. Point angle: 130. Helix angle: High. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Supply unit. All diameters - 1 pce. Manufactured to DIN338RN.

Series 1060 - Metric

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT3) - Metric

Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Inch

Dormer Stub Drills

A920 - HSCo PFX Stub Drills
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow.Size Range: 1.0-20.0mm. Manufactured to BS 323, DIN1897, ansi.

A920 - HSCo PFX Stub Drills - Inch

Sherwood Jobber Drills Bright Finish HSS

General-purpose drills for steel, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328/DIN338RN. Bright finish: drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.

Series J100 - Metric - Bright Finish

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Gauge Sizes

Kennedy® Stub Length Drills Carbide

For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic. Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6. Manufactured to DIN 6539.

Tolerances:
Cutting Dia. plus 0.000mm - 0.015mm.
Shank Dia. plus 0.000mm - 0.030mm.

Kennedy® Carbide Stub Length Drills - Metric

SwissTech Heavy Duty Jobber Drills HSS-Co 8% Cobalt

The addition of up to 8% Cobalt allows higher speeds to be used without reducing the life of the tool, increasing productivity. 28 Helix and 135 Point. Manufactured to DIN338RN. Point to DIN1412C.

Series 1020 - Metric

Dormer Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A100