Sherwood Spotting Drills HSS-E

These specially designed drills produce accurate and true positional hole starts for follow-up drills. They provide exceptional alignment accuracy, achieved due to short flute and overall lengths and no body clearance. This very short design allows chucking very close to the point so that they will produce a true start or center. Traditional twist drill bits may tend to wander when started on an unprepared surface. Once a bit wanders off-course it is difficult to bring it back on center. A spot drill bit will provide a far better starting point as it is short and has a reduced tendency to wander. For accurate and fast spotting on NC machines, jig drills and other capital-intensive boring machines. Also suitable for countersinking and chamfering of tapping holes in one operation.
90 point angle - Offers hole chamfering and spotting with one tool.
120 point angle - Specifically for spotting and closely matches a typical drill point. The cutting edges of the following drill will engage easily for perfect hole location.
For all dimensional specifications please refer to our catalogue.

Series C530 - 120 Degree

Guhring Production Jobber Drills HSS-Co 5%

Rigid, high-heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. Limited suitability for special alloys such as hastaloy, inconel, nimonic etc. Manufactured to DIN338.

Series 605 - Metric

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT1) - Metric

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT1) - Metric

Guhring Micro-Precision Drills HSS-Co

Series 301 & 660 are for use in general precision engineering, especially the instrument and clock making industries. Specially designed for drilling high alloyed steels. Manufactured to DIN1899.

For all dimensional specifications please refer to our catalogue.

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT1) - Metric

Guhring Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series 205

Guhring Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series 205

Sherwood Long Series Drills Steam Tempered HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

SwissTech Jobber Drills HSS TiN Coated

General-purpose drill, to drill steels with a tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. TiN coating provides longer tool life. Point angle: 118. Helix angle: Normal. Web thickness: Normal. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufactured to DIN338RN.

Series 1001