Dormer HSCO Jobber Drills

A941 (10xD) - 1.0-16.0mm, 3/64-5/8 Inch

A941 Long Series HSCO Jobber Drills Coated

A941
Excellent for: Carbon/alloy steels, stainless, cast iron and aluminium
Good for: Titanium and copper

A520 - HSS ADX TiN Coated Stub Drills

Designed for use where high productivity and accuracy are required. Unique flute geometry. 130° point angle. TiN coating for increased tool life & performance. Manufactured to DIN1897.

Dormer Jobber Drills TiN Tipped

Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.

Series A002

Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Metric

Dormer Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A100

Dormer HSCO Jobber Drills

A941 (10xD) - 1.0-16.0mm, 3/64-5/8 Inch

A941 Long Series HSCO Jobber Drills Coated

A941
Excellent for: Carbon/alloy steels, stainless, cast iron and aluminium
Good for: Titanium and copper

Dormer Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A100

Dormer HSCO Jobber Drills

High productivity one-hit drilling across a wide range of materials.
130° special point geometry ensures consistent hole size and quality throughout the full depth of the hole.
Size Range: A940 (10xD) - 1.0-20.0mm, 3/64-25/32 Inch.

A940 Long Series HSCO Jobber Drills Bright

A940
Excellent for: Carbon/alloy steels, stainless and titanium
Good for: Cast iron, copper, aluminium and thermoplastics

Dormer Jobber Drills Solid Carbide

General-purpose carbide drills. 120 four-facet point for accurate centering and improved hole quality. Bright finish.

Series R100 - Metric

Dormer Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series A130 (MT1) - Metric