Guhring Stub Drills HSS

Ideally suited for portable drill applications where the shorter flute and stub length offer the extra rigidity normally associated with fixed drilling. Manufactured to BS328:Part 1:1986/DIN1897RN.

Series 223

Guhring Stub Drills Carbide SL

Carbide drills deliver a quantum leap in high speed holemaking performance and tool life that manufacturers have been asking for. Carbide tooling provides faster cutting rates, longer tool life, better positional and dimensional accuracy and improved surface finish. Short cycle times and tighter tolerances translate into maximum machine utilizations, better part quality and optimum holemaking cost savings.

Series 5516

Guhring Production Jobber Drills HSS-Co 5%

Rigid, high-heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. Limited suitability for special alloys such as hastaloy, inconel, nimonic etc. Manufactured to DIN338.

Series 605 - Inch

Guhring Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series 205

Guhring GT100 Jobber Drills HSS

HSS GT100 jobber drills. For drilling in difficult conditions when swarf congestion prevents an adequate flow of coolant. For use in steel and cast iron having a hardness of up to 1000N/mm2. Not recommended for nickel-chrome steels or similar material. Manufactured to BS 328/DIN 338.

Series 549 - Metric

Guhring Production Jobber Drills HSS-Co 5%

Rigid, high heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. TiN coated gives greater wear resistance and longer tool life. Limited suitability for special alloys such as Hastelloy, Inconel, Nimonic etc. Manufactured to DIN338.

Series 657 - Metric

Guhring Stub Drills HSS TiN Coated

For use in automatic and capstan lathes. For use with hand drilling machines in drilling thin sections, such as sheet metal, car bodies etc. Type N. Manufactured to DIN1897. 118 point angle.

Series 653

Guhring Production Drills

Guhring No.5523 Jobber Drill HSS-Co have a tough cobalt substrate that delivers high performance at low cost to produce a general purpose drill for the machining of steel and cast steel (alloyed and unalloyed), , grey cast iron, malleable cast iron, spheroidal graphite iron, sintered iron and graphite with high concentricity characteristics.

No.5523 Jobber Drill HSS-Co

Guhring Production Jobber Drills HSS-Co 5%

High heat resistant drill with wide chip space. Suitable for drilling alloyed and unalloyed steels and castings with a high tensile strength over 800N/mm2. Particularly suitable for drilling hot and cold rolled steels. Manufactured to DIN338.

Series 658 - Metric

Guhring Production Jobber Drills HSS-Co 5%

Solid Carbide Jobber drills are especially suitable for drilling cast steels, grey cast iron, chilled cast iron, austenitic manganese steels, bronzes, light metals and non-ferrous metals. Furthermore suitable for the economic machining of abrasive materials (AlSi-alloys), fibre-reinforced plastics and other Duroplastics liable to cause severe abrasion on cutting lips and lands.

Series 5517 - Metric