Kennedy® Edge & Centre Finders - Cylinder Type

For fast accurate work location. Made from tool steel and hardened all over, they can be used on flat surfaces, straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines.

Combination - Edge & Centre Finders

Edge & Centre Finders

Much time and trouble is taken in locating holes, or in other machine operations, which must be carried out accurately, relative to a given datum. Jig borers are available where extreme accuracy is required and expensive equipment is warranted. In the great majority of cases, however, an accuracy of the order of .001" is sufficient and a jig borer is not available. In such cases the Huffam centre locator provides a quick and efficient means of establishing the required position and can be used on any machine by an unskilled operator. It will indicate the relation between the centre line of any machine spindle and a datum face to within .0005" by the 'run-off' method and to within .0002" by using the light 'line' method. Although ideally suited for use on mills the Huffam centre locator can also be used on drills, lathes or any other rotating machinery employing a chuck.

Edge & Centre Finders

Much time and trouble is taken in locating holes, or in other machine operations, which must be carried out accurately, relative to a given datum. Jig borers are available where extreme accuracy is required and expensive equipment is warranted. In the great majority of cases, however, an accuracy of the order of .001" is sufficient and a jig borer is not available. In such cases the Huffam centre locator provides a quick and efficient means of establishing the required position and can be used on any machine by an unskilled operator. It will indicate the relation between the centre line of any machine spindle and a datum face to within .0005" by the 'run-off' method and to within .0002" by using the light 'line' method. Although ideally suited for use on mills the Huffam centre locator can also be used on drills, lathes or any other rotating machinery employing a chuck.

Edge & Centre Finders

Much time and trouble is taken in locating holes, or in other machine operations, which must be carried out accurately, relative to a given datum. Jig borers are available where extreme accuracy is required and expensive equipment is warranted. In the great majority of cases, however, an accuracy of the order of .001" is sufficient and a jig borer is not available. In such cases the Huffam centre locator provides a quick and efficient means of establishing the required position and can be used on any machine by an unskilled operator. It will indicate the relation between the centre line of any machine spindle and a datum face to within .0005" by the 'run-off' method and to within .0002" by using the light 'line' method. Although ideally suited for use on mills the Huffam centre locator can also be used on drills, lathes or any other rotating machinery employing a chuck.

Kennedy® Edge & Centre Finders - Cylinder Type

For fast accurate work location. Made from tool steel and hardened all over, they can be used on flat surfaces, straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines.

Combination - Edge & Centre Finders

Edge & Centre Finders

Much time and trouble is taken in locating holes, or in other machine operations, which must be carried out accurately, relative to a given datum. Jig borers are available where extreme accuracy is required and expensive equipment is warranted. In the great majority of cases, however, an accuracy of the order of .001" is sufficient and a jig borer is not available. In such cases the Huffam centre locator provides a quick and efficient means of establishing the required position and can be used on any machine by an unskilled operator. It will indicate the relation between the centre line of any machine spindle and a datum face to within .0005" by the 'run-off' method and to within .0002" by using the light 'line' method. Although ideally suited for use on mills the Huffam centre locator can also be used on drills, lathes or any other rotating machinery employing a chuck.

Kennedy® Edge & Centre Finders - Cylinder Type

For fast accurate work location. Made from tool steel and hardened all over, they can be used on flat surfaces, straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines.

Edge Finders

Kennedy® Edge & Centre Finder - 5 Piece Set

Consists of a chuck body and four contact arms. Designed to check 'run-out' or concentricity, straightness and alignment. Will indicate the position of a datum point on a component or fixture from the centre line of a machine spindle. Suitable for use on drill presses, lathes, milling machines, borers etc.

Ground, hardened and polished contact arms, for accurate location.
Quick change "snap fit" contact arms and body.
Fast, effective way of locating working centres.
Unique universal indicator holder.

Overall Packaging dimensions: 124(W) x 14(D) x 135(H)mm.

Kennedy® Edge & Centre Finders - Cylinder Type

For fast accurate work location. Made from tool steel and hardened all over, they can be used on flat surfaces, straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines.

Double Edge

Edge & Centre Finders

Much time and trouble is taken in locating holes, or in other machine operations, which must be carried out accurately, relative to a given datum. Jig borers are available where extreme accuracy is required and expensive equipment is warranted. In the great majority of cases, however, an accuracy of the order of .001" is sufficient and a jig borer is not available. In such cases the Huffam centre locator provides a quick and efficient means of establishing the required position and can be used on any machine by an unskilled operator. It will indicate the relation between the centre line of any machine spindle and a datum face to within .0005" by the 'run-off' method and to within .0002" by using the light 'line' method. Although ideally suited for use on mills the Huffam centre locator can also be used on drills, lathes or any other rotating machinery employing a chuck.