Self Tapping Screws

Self-tapping steel screws. AB zinc-plated. For use on sheet metal and other malleable materials. DIN: 7982 C Z.

PoziDriv - Countersunk (Inch)

Socket Set Screws

High tensile alloy steel. Grade 14.9. DIN 913.

Metric sizes - Flat Point - Self Colour

For use where parts are frequently reset. This style of point causes the least amount of damage to the component it locks on to. Can be used against hardened shafts, preferably with a ground flat for improved surface contact. Ideal for use as an adjusting screw and in thin wall thicknesses and on soft plugs.

Socket Set Screws

High tensile alloy steel. Grade 14.9. BS 2470. For quick and permanent location of pulleys, collars and gears on shafts. Will hold fast even in poorly tapped holes. Interrupted profile of clamping face resists loosening due to vibration. Sizes above 1/4? are generally counterbored to provide maximum clamping efficiency.

Inch (UNC) - Knurled Cup Point - Self Colour

Socket Head Shoulder Screws

High Grade Alloy Steel to BS EN ISO 898/1 Grade 12.9. Suitable for replacing costly components such as shafts, pivots, guides, pins, linkages and trunion mountings. Also commonly used in the die mould industry. Maximum operating temperature (unplated): 300C. Dimensions to Body Diameter Tol h8.

Metric Sizes - Standard Self Colour

Socket Head Flange Button Screws

An extra wide flange below the button head makes these fasteners ideal for fixing strips cover plates and sheet metal housings that require a greater load spread. Dimensions to BS EN ISO 898/1 Grade 10.9 DIN 267.

Metric Sizes - Standard Self Colour

Socket Head Countersunk Screws

High Grade Alloy Steel to BS EN ISO 898/1 Grade 10.9. Suitable for all high tensile applications. Maximum operating temperature (unplated): 300C. For applications that require a flush finished surface. Precisely controlled countersink angle allows maximum flushness and sidewall contact. Dimensions to DIN 7991.

Metric Sizes - Standard Self Colour

Socket Head Shoulder Screws

High Grade Alloy Steel to BS EN ISO 898/1 Grade 12.9. Suitable for replacing costly components such as shafts, pivots, guides, pins, linkages and trunion mountings. Also commonly used in the die mould industry. Maximum operating temperature (unplated): 300C. Dimensions to Body Diameter Tol h8.

Inch (UNC) - Standard Self Colour

A2 Stainless Steel - Countersunk

A2 Stainless Steel - Countersunk

Socket Set Screws

High tensile alloy steel. Grade 14.9. BS 2470. For quick and permanent location of pulleys, collars and gears on shafts. Will hold fast even in poorly tapped holes. Interrupted profile of clamping face resists loosening due to vibration. Sizes above 1/4? are generally counterbored to provide maximum clamping efficiency.

Inch (BSF) - Knurled Cup Point - Self Colour

Kennedy Thread Repair

Kennedy Professional Thread Repair Wire Inserts are the easiest and quickest inserts to install to repair damaged or worn threads, you simply screw the insert into the pre-drilled and tapped hole, until the drive tang breaks off. They can be used with plastics or other materials provided that the material is strong enough to withstand the expansion of the insert as the screw thread locks into the wall of the hole. They are also suitable for new applications where, because of their mechanical strength benefits their introduction may result in the use of thinner sections or lighter parent materials without sacrificing thread strength they can also be used for converting from metric to inch and vice versa.

Most inserts are 1.5x diameter for length. For example:- M6 is 9mm long.
Other lengths are available on request.

Available in Metric, UNC, UNF, BSF, BSP and BSW sizes.

For all dimensional specifications please refer to our catalogue.

Wire Thread Insert Kits (Metric)

Each Kennedy Professional Thread Repair Wire Insert Kit is supplied complete with a Hand Tap, Inserting Tool and Inserts.