Kennedy® Thredfloer Fluteless Taps

Form rather than cut the thread in almost any ductile material. These include aluminium, brass, copper, carbon steels, zinc and magnesium alloys and even some stainless steels. The material is "cold formed" into the relevant thread and has the advantage of being a full form thread unlike normal cut tapped holes. This make the thread stronger. The forming operation does not create chips so swarf contamination and blockage is illiminated and tap breakage reduced. Because there is no consideration for chip evacuation, Thredfloer taps can be run at higher cutting speeds and reduced cycle times. Lubrication grooves are a feature of all Thredfloer taps of M3.0 and over. These allow lubrication to reach the end of the tap to maintain tool life and to prevent damage from "Hydraulic Blow Out".

Metric Coarse

HSS - EV. Oxide Finish. Tolerance 6H. Manufactured to DIN 371.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Tap Set Metric Fine Straight Flute Ground Thread HSS

Sherwood HSS taper taps are used to start cutting the thread they is tapered back from the end 6 to 10 threads before a fully threaded diameter is reached this allows the tap to be positioned easily and correctly before it starts to cut the thread.

The Second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before full thread diameter is reached.

The Plug tap cuts threads to the bottom of a blind hole. It is only necessary to use the full set of taps when a blind hole is to be tapped.

Each set of Sherwood taps contain one taper, second and plug lead tap.

E002 TiN ISO 529 Cross Tap Metric Taps

Titanium Nitride Finish

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.

Die Nuts Metric Fine HSS

EP31 DIN 2184-1 Spiral Point UNF Taps

Steam Tempered Finish

Dormer Machine Taps

Dormer machine tap ranges have been designed for use with a high quality floating tool holder. For synchronous tapping on CNC machines with a rigid tapping cycle, Dormer SynchroFlex tool holders are recommended for a precisely defined minimum compensation in order to maximise machine performance. This is particularly important for larger sizes of spiral flute taps.

Available in spiral point for through holes and spiral flute for blind holes with 45 spiral angle. The three radii profile, with a constant rake angle all along the flute, is specially designed to give an optimum performance and chip evacuation in materials being threaded.
Surface Treatment
Special gold finish with bright flutes/thread, or steam tempering (blue) guarantee a smooth cutting action with less build up on the cutting edge.

Manufactured from HSS-XS1 premium quality vanadium powder steel and HSCo for superior toughness and edge strength, to give a high resistance to wear and long tool life.

All taps are available in Metric thread form initially. Thread forms Metric Fine, UNC, UNF and G will be stocked from September 2010.
Short Thread Length
The short thread length means low torque and better chip evacuation.
Thread Depth
Threading to depths of up to 2.5 x Diameter.

EP00 Series Spiral Point Metric Machine Tap

Dormer Spiral Point Metric Machine Taps for through holes. With gold finish with bright flutes.
Taper lead to DIN form B.
Tapping tolerance to 6H.
Max depth 2.5 x D.

EP21 DIN 2184-1 Spiral Point UNC Taps

Steam Tempered Finish

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Tap Set Metric Fine Straight Flute Ground Thread HSS

Sherwood HSS taper taps are used to start cutting the thread they is tapered back from the end 6 to 10 threads before a fully threaded diameter is reached this allows the tap to be positioned easily and correctly before it starts to cut the thread.

The Second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before full thread diameter is reached.

The Plug tap cuts threads to the bottom of a blind hole. It is only necessary to use the full set of taps when a blind hole is to be tapped.

Each set of Sherwood taps contain one taper, second and plug lead tap.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Second Tap Metric Coarse Straight Flute Ground Thread HSS

The Sherwood second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before a fully threaded diameter is reached. If threading a blind hole a Plug tap will be required to cut threads to the bottom of the hole.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Spiral Point Tap BSPF (British Standard Pipe Fine) Ground Flute HSS

A spiral point tap has a chiselled point that pushes the metal chips ahead of the forming threads. This is useful when tapping through-holes (holes that extend through the work piece).

Spiral Point taps are not recommended for use in blind holes: the accumulation of chips can bind and break the tap.