Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Spiral Flute Tap Metric Coarse Ground Thread HSS

Spiral flute taps are used for machine tapping of blind holes as the have a spiral flute that channels the swarf back behind the tap and out of the hole along the flute.

Dormer Taps

Dormer MTT-X Series taps are manufactured from HSS-X1 Steel with a Bright finish, they are right Hand Cutting.

Manufactured to ISO 529
Spiral Flute for threading blind holes.
Taper lead to DIN form C.
Tapping tolerance to 6H.
Max Depth 2.5 x D.
Helix angle 48.

For all technical and dimensional specifications please refer to our catalogue.

MTT-X Series E023 Spiral Flute UNC (Unified Coarse) Tap

Swiss+Tech® HSS "Purple Ring" Taps

Manufactured to DIN 371/376.

Left Hand Spiral Flute - HSS-PM Nitride Finish ISO metric Coarse

For through holes. Taper lead to DIN form D (5 x P). Tapping tolerance to 6HX 2BX. Helix angle 15°.

Kennedy® High Performance Machine Taps

Made from a super grade high speed steel with extra vanadium content. This has a distinct advantage with taps, by increasing wear resisting properties and extending tool life significantly. These taps are intended for general application where consistent results and improved tool life are important. Threads can be produced in a range of steels, including stainless and cast steels as well as some long chip non-ferrous materials.

Machine Taps Spiral Point Metric Coarse HSS - EV

With straight flutes and short fluted helix at point. Ideal for tapping through holes as swarf is directed ahead of the tap. Flutes are narrower than those of taps required to pull swarf towards the shank and act as lubricant channels, giving greater tap rigidity. Manufactured to BS 949: Part 4: 1990 and ISO 529 : 1975. Tolerance 6H.
Bright finish: standard finish for tapping most materials including low silicon aluminiums, brass, mild steels (low volume) stainless, copper.

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.



BSF (Fine)

EP21 DIN 2184-1 Spiral Point UNC Taps

Steam Tempered Finish

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Fluteless Tap Metric Coarse HSS

Sherwood Dies

Sherwood UNC (Unified Coarse) HSS dies are used in diestocks to produce external screw threads.

Thread form to: BS 1580

For all technical and dimensional specifications please refer to our catalogue.

Dies UNC (Unified Coarse) Ground Thread HSS

Swiss+Tech® HSS "White Ring" Taps

Manufactured to DIN 371/376.

Straight Flute - HSS-EV Nitride Finish ISO Metric Coarse

For blind holes. Taper lead to DIN form C (2.5 x P). Tapping tolerance to 6HX 2BX.

Sherwood Dies

Sherwood dies are for use in die stocks to cut external screw threads on metal rod, the split in the die allows the adjusting screws of the diestock to compress or expand the die to accommodate for slight variations in size of the material being threaded or die sharpness. Sherwood dies are available as Metric Fine, Metric Coarse, UNF, UNC, BA, BSF, BSW, BSPT, BSPF, NPT cutting threads all the dies are manufactured from HSS with precision ground threads to the applicable standard.

For all technical and dimensional specifications please refer to our catalogue.

Ground Thread Dies Left Hand Metric Coarse HSS