Kennedy® Jigsaw Blades

Manufactured from high quality steels to meet the demands of most industrial and DIY applications. Supplied display carded. High teeth per inch (TPI) blades will be slower cutting and produce a better edge finish. Low teeth per inch blades will be faster cutting but produce coarse edges on the workpiece. Different materials will also give different edge finishes depending on the make up of the material and direction of cut in relation to the direction of the grain. When cutting in some metals lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw baseplate reducing the gap around the blade and reducing the splinter area. Another technique is to score a guide line on the wood creating a pre-cut line that must then be followed accurately. The last technique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made.

?U? Type Suitable for Black & Decker and Hitachi DIY. Tungsten Carbide (Pack 1)

Capacities: Plastic - 20.0mm. 30 grit. For brick, slate and ceramics. Effective length: 54mm. Equivalent to B&D A5192.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T244D)
Application: wood 60mm, plastics 50mm. For cutting curves.
Blade: HCS medium duty, side set teeth.
Tooth pitch: 4.0mm.

Effective length: 75mm.

Pack of 5.

Kennedy® "Contractor Packs" Jigsaw Blades

The most popular 'T' style blades bulk packed in 20's for economy. Supplied in telescopic 'pocket' cases that are ideal for the industrial user.

HCS - Medium Duty (Pack 20)

Kennedy® Jigsaw Blades

Manufactured from high quality steels to meet the demands of most industrial and DIY applications. Supplied display carded. High teeth per inch (TPI) blades will be slower cutting and produce a better edge finish. Low teeth per inch blades will be faster cutting but produce coarse edges on the workpiece. Different materials will also give different edge finishes depending on the make up of the material and direction of cut in relation to the direction of the grain. When cutting in some metals lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw baseplate reducing the gap around the blade and reducing the splinter area. Another technique is to score a guide line on the wood creating a pre-cut line that must then be followed accurately. The last technique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made.

Straight Shank Suitable for Fein, Wolf and Kress. HCS - Medium Duty (Pack 5)

Capacities: Wood - 50mm, Plastic - 30mm. Tooth pitch: 4.0. Effective length: 75mm. Tapered & ground teeth. Equivalent to Wolf 91480.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HSS - Heavy Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T127D)
Application: steel 3 - 6mm, aluminium 3 - 15mm, plastics 20mm.
Blade: HSS heavy duty, side set teeth.
Tooth pitch: 3.0mm.

Effective length: 75mm.

Pack of 5.

Kennedy® Jigsaw Blades

Manufactured from high quality steels to meet the demands of most industrial and DIY applications. Supplied display carded. High teeth per inch (TPI) blades will be slower cutting and produce a better edge finish. Low teeth per inch blades will be faster cutting but produce coarse edges on the workpiece. Different materials will also give different edge finishes depending on the make up of the material and direction of cut in relation to the direction of the grain. When cutting in some metals lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw baseplate reducing the gap around the blade and reducing the splinter area. Another technique is to score a guide line on the wood creating a pre-cut line that must then be followed accurately. The last technique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made.

Two Hole Type Suitable for old style Makita. HCS - Medium Duty (Pack 5)

Capacities: Wood - 40.0mm, Plastics 30.0mm. Tooth pitch: 3.0. Effective length: 60mm. Side set teeth. Equivalent to Makita No.3.

Kennedy® Jigsaw Blades

Manufactured from high quality steels to meet the demands of most industrial and DIY applications. Supplied display carded. High teeth per inch (TPI) blades will be slower cutting and produce a better edge finish. Low teeth per inch blades will be faster cutting but produce coarse edges on the workpiece. Different materials will also give different edge finishes depending on the make up of the material and direction of cut in relation to the direction of the grain. When cutting in some metals lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw baseplate reducing the gap around the blade and reducing the splinter area. Another technique is to score a guide line on the wood creating a pre-cut line that must then be followed accurately. The last technique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made.

Straight Shank Suitable for Fein, Wolf and Kress. HCS - Heavy Duty (Pack 5)

Capacities: Steel 3.0 - 6.0mm, Aluminium 1.0 - 3.0mm, Plastics 6.0mm. Tooth pitch: 3.0. Effective length: 50mm. Wavy set teeth. Equivalent to Wolf 91485.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T101D)
Application: wood 60mm, plastics 30mm.
Blade: HCS medium duty, tapered and ground.
Tooth pitch: 4.0mm.

Effective length: 75mm.

Pack of 5.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HSS - Heavy Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T218A)
Application: steel 1.5 - 4mm, aluminium 1.5 - 4mm.
Blade: HSS heavy duty, wavy set tooth form. For cutting curves. Tooth pitch: 1.2mm.

Effective length: 48mm.

PAck of 5.

Kennedy® "Contractor Packs" Jigsaw Blades

The most popular 'T' style blades bulk packed in 20's for economy. Supplied in telescopic 'pocket' cases that are ideal for the industrial user.

HSS - Heavy Duty (Pack 20)