Sherwood 4 Flute Ball Nosed End Mills Plain Shank Solid Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute Ball Nosed End Mills

SwissTech 45 Fine Pitch Ripper Cutters Weldon Shank HSS-E PM TiALN Coated

Centre cutting. Shank to DIN 1835B. Cutting diameter to js12. Shank diameter to h6. The combination of HSS-E PM and TiALN provides a cutter that is ideally suited to dry and semi-dry machining of materials up to 45 HRC, stainless steels and Aerospace alloys.

For all technical and dimensional specifications, please refer to our catalogue.

Series 90 Regular EHP-4WR PM Coated

Dimensions to DIN 844.

Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS

Used for profile milling and producing open slots. Bright finish. Flute type : 30° Helix. Manufactured to BS 122 : Part 4 : 1980.

Long Series E430T - Metric

For all dimensional specifications please refer to our catalogue.

Sherwood Fine Pitch Ripper Cutters Weldon Shank HSS-EV

Multi flute ripper cutters. Manufactured from sintered HSS-EV extra vanadium steel. Knuckle form, h8 tolerance, standard length. Dimensions to DIN 844. Shank to DIN 1835D.

Regular Series

Dormer 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30 helix. Manufactured to BS 122: Part 4: 1980.
Material:
XS1 HSS powder metallurgy steel. This provides a finer and more consistent grain structure than HSCo resulting in a tougher product able to more easily withstand the shock load and intermittent cutting associated with milling operations. Tool life and wear resistance, exceeds standard HSS and is comparable to HSCo cutters. Superior edge strength and rigidity, resulting in improved surface finish and slot consistency equal to and in some cases better than HSCo. A productivity increase of around 40% over existing HSS cutters. Flute and overall lengths: to BS122/4.
Finish: bronze finish: provides a uniform structure and hardness at the tool surface, whilst also aiding tool identification.

For all dimensional and technical information please refer to our catalogue.

Short Series C191 - Metric

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Chatter is also significantly reduced. Centre cutting as standard. Manufactured to Ansi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 3 Flute - Inch

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

45° Corner Angle - Metric (Form C)

For all dimensional and technical specifications please refer to our catalogue.

Kennedy® Long Series Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 2 Flute Slot Drills - Metric

Brooke Cutting Tools Straight Tooth Side & Face Milling Cutters HSS

Designed with strip land and tooth form to give strength and more chip clearance. Special note is to be taken of the form at the back of the teeth which gives greater support to the cutting edge. The cutters are well adapted for a wide variety of production operations and are commonly used in pairs for straddle milling.

For all dimensional specifications please refer to our catalogue.

SwissTech Shank Milling Cutters

The latest enhancement of the SwissTech range, these cutters deliver excellent performance when cutting difficult materials, even at high speeds.

Manufactured from premium PM (Powder Metallurgy) tool steel, with an excellent cutting geometry. Designed for strength and rigidity, minimising vibration in high speed cutting applications and providing improved productivity.

These cutters are further enhanced by the SwissTech Peak Power coating, suiting dry cutting applications, having higher oxidization resistance and hot-hardness than conventional TiALN or TiCN coatings, withstanding the high thermal loads associated with high speed cutting applications.

Series 97 2 Flute Ball Nose Slot Drills HSS-E PM Coated

Centre cutting.
Weldon shank to DIN 1835B.
Shank diameter to h6.
Dimensions to
DIN 844.