HSS-Co. 8% Plain Shank Milling Cutter 4 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots.
Bright finish. Flute type: 30° helix.
Overall dimensions to DIN 844.
Plain shank to DIN 1835A.

Metric Tolerances
Nominal Dia. Limits of Tolerance
Up to 38mm 0.0630 -0.0130
Above 38mm 0.1250 -0.0000

Long Series

Sherwood 2 Flute Long Series Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright Finish. Flute Type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional specifications please refer to our catalogue.

Inch

Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS-Co

Used for profile milling and producing open slots. Bright finish. Flute Type : 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Long Series Type E431T - Metric

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Ball Nose Endmill 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% - Inch

SwissTech 3 Flute Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 07 Long SDN-3WL TiCN Coated

Dimensions to DIN 844.

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

45° Corner Angle - Metric (Form C)

For all dimensional and technical specifications please refer to our catalogue.

Swiss+Tech 2 Flute Slot Drills Threaded Shank HSS-Co 8%

Centre cutting. Threaded shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 28 Short SDN-2TS TiCN Coated

Dimensions to DIN 327

OSG Endmills Carbide

OSG WX-EDS endmills are manufactured from high performance micro grain carbide with Ultra WX coating (multi layered composite TiALN).

For high speed milling in a wide range of applications.
Stub length centre cutting with sharp corner edge.

The Ultra WX coating has been developed to improve performance in a wide range of materials including nonferrous materials, mild steels, and refined steels This stable performance remains consistent in both wet and dry applications and is intended for a wide range of cutting conditions, from low speed/reduced cutting force applications to high speed/high cutting force applications.

For all technical and dimensional specifications please refer to our catalogue.

WX-EDS Series 2 Flute Endmill Plain Shank Carbide

SwissTech 4 Flute Corner Radius End Mills Plain Shank Q-Coat Carbide

Centre Cutting. To Manufacturers Standards. Cutting diameter to e8, Shank diameter to h6. ?Q-Coat? Coating has been specifically developed to give carbide cutters the ?edge? when faced with severe machining conditions. Materials up to 66 HRC. Dry cutting. Die and Mould machining. Reduced coolant usage and disposal. Up to 100% longer cutter life. Reduced manufacturing costs. A multi-layer coating capable of operating at higher speed and feed. Excellent oxidisation resistance. High speed machining. Surface hardness 3300HV. Surface coefficient against steel 0.25. Thickness of coating 305um. Maximum working temperature 850. Re-coating service also available.

For all technical and dimensional specifications please refer to our catalogue.

Series 86 Regular ECQ-4PR Q-Coat

SwissTech 4 & 6 Flute End Mills Threaded Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B.
Shank cutting diameter to plus0.04 -0.0.

Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 37 Long EML-4TL TiALN Coated

Dimensions to DIN 844.