SwissTech High Helix End Mills Weldon Shank HSS-E PM TiALN Coated

Centre cutting. Shank to DIN 1835B. Cutting diameter to js12. Shank diameter to h6. The combination of HSS-E PM and TiALN provides a cutter that is ideally suited to dry and semi-dry machining of materials up to 45 HRC, stainless steels and Aerospace alloys.

For all technical and dimensional specifications, please refer to our catalogue.

Series 92 Long EHP-6WL PM Coated

SwissTech 2 Flute Slot Drills Threaded Shank HSS-Co 8%

Centre cutting. Threaded shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 28 Short SDH-2TS HSS-Co 8%

Dimensions to DIN 327

Kennedy® 2 Flute Milling Cutters for Aluminium Carbide Al-Karb Ultrafine Micrograin

Centre cutting as standard. An advanced tool geometry designed for cutting aluminium and other non-metallic, non-ferrous materials requiring high machining rates. Al-Karb cutters will out-perform conventional end mills on these materials as the flute design allows maximum chip removal.Short Series

Short Series 2 Flute - Metric

Dijet Carbide End Mills

Dijet AL-SEELS series End Mills are for profiling & Slotting in Aluminium and Alloys

AL-SEEL-2 Long Series Carbide End Mill

Dijet AL-SEELS series Carbide end mill specification:
Sharp corner.
Helix angle 45.
2 flute.
Centre cutting.
Regular cutting edge.
Shank cutting diameter to 0.04-0.0
Weldon shank to DIN 1835B.

SwissTech 2 Flute Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 01 Short SDL-2WS TiALN Coated

Dimensions to DIN 327.

Kennedy® 4 Flute Double-Ended End Mills Plain Shank Solid Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting. Manufactured to ANSI Standards.

For all technical and dimensional specifications please refer to our catalogue.

Regular Series 4 Flute Double End - Metric

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

3 Flute
Centre cutting as standard. Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 3 Flute Slot Drills - Inch

HSS-Co. 8% Plain Shank Milling Cutter 4 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots.
Bright finish. Flute type: 30° helix.
Overall dimensions to DIN 844.
Plain shank to DIN 1835A.

Metric Tolerances
Nominal Dia. Limits of Tolerance
Up to 38mm 0.0630 -0.0130
Above 38mm 0.1250 -0.0000

Long Series

SwissTech 45 High Helix End Mills Plain Shank Q-Coat Carbide

Centre Cutting. To Manufacturers Standards. Cutting diameter to e8, Shank diameter to h6. ?Q-Coat? Coating has been specifically developed to give carbide cutters the ?edge? when faced with severe machining conditions. Materials up to 66 HRC. Dry cutting. Die and Mould machining. Reduced coolant usage and disposal. Up to 100% longer cutter life. Reduced manufacturing costs. A multi-layer coating capable of operating at higher speed and feed. Excellent oxidisation resistance. High speed machining. Surface hardness 3300HV. Surface coefficient against steel 0.25. Thickness of coating 305um. Maximum working temperature 850. Re-coating service also available.

For all technical and dimensional specifications please refer to our catalogue.

Series 72 Regular EHQ-6*PR Carbide Q-Coat

*Number varies according to the number of flutes.

Sherwood 2 Flute Long Series Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright Finish. Flute Type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional specifications please refer to our catalogue.

Inch