Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Shielded Type

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Self-Aligning Ball Bearings

2200 & 2300 Series self-aligning ball bearings are double row with a concave raceway to allow approximately 4° of misalignment. These are cylindrical type but are also available with seals & taper bore for use with adaptor sleeves.

Cylinder Bore

SNR Deep Groove Ball Bearings

Open type 25mm bore bearing for the free circulation of either oil or grease.
Size: 25 x 47 x 14mm.

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Shielded Type

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Self-Aligning Ball Bearings

2200 & 2300 Series self-aligning ball bearings are double row with a concave raceway to allow approximately 4° of misalignment. These are cylindrical type but are also available with seals & taper bore for use with adaptor sleeves.

Taper Bore

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Angular Contact Bearings - Double Row

Double-row angular-contact ball bearings accept axial loads in both directions and can be used singly, as dual bearing units.? withstand axial loads in both directions? accept relatively high speeds of rotationThe construction of these bearings limits them to very small misalignment values, in the range of 0.06.

Series 32...B, 33...B

Contact angle 32, with filling slots and accept axial loads (higher loads than Type A) in a predominant direction. Cage in pressed steel, synthetic material or machined brass.

SNR Bearings

SNR has developed a complete range of high quality ball thrust bearings. Thrust bearings are designed to maintain the shaft in one single direction. They admit low rotating speeds and sustain high axial loads.

You are strongly advised against submitting them to radial loading. Ball thrust bearings are comprised of separate items facilitating installation and maintenance. Grease and oil lubrication is feasible.

Applications: vertical shaft, lathe tailstock, plate-type pumps.

51100 Series Ball Thrust Bearings