SNR Deep Groove Ball Bearings

Rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects.

Sealed Deep Groove Ball Bearings

Dimensions to IS015

SNR Deep Groove Ball Bearings

With Shields

Angular Contact Bearings - Double Row

Double-row angular-contact ball bearings accept axial loads in both directions and can be used singly, as dual bearing units.? withstand axial loads in both directions? accept relatively high speeds of rotationThe construction of these bearings limits them to very small misalignment values, in the range of 0.06.

Series 32...A, 33...A

Contact angle 25, no filling slots and can accept axial loads in both directions. These bearings have synthetic material cages.

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Shielded type:

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Shielded type:

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

NTN SNR Thermometer

The NTN SNR Infrared thermometer LASER TEMP 301 is an infrared thermometer used to diagnose, inspect and check any temperature. Thanks to its elaborated optical system, it allows an easy and accurate measurement of little distant targets. Ideal for rapidly establishing an initial diagnosis of how equipment is operating with complete safety, precise remote or contact temperature measurements.

Features include:
Wide measurement range: -50C to +850C.
High degree of precision using the laser targeting device.
Internal memory which can save up to 20 measurements.
Response times less than 1 sec.
Simple to use, can be configured in C or F.
Back-lit display for easy reading.

Laser Temp 301 Infrared Thermometer

Laser Temp 301 Specification:
Spectral response: 8-4mm
Optical: D.S : 30:1 (50mm at 1500mm)
Response time: Less than 1 second
Temperature range: From -50 to +850C
Accuracy*:
From -50 to -20C : plus/minus 5C
From -20 to +200C : plus/minus 1.5% of reading plus/minus 2C
From +200 to +538 C : plus/minus 2% of reading plus/minus 2C
From +538 to +850C : plus/minus 3.5% of reading plus/minus 5C
Display resolution: 0.1C
Emissivity: Adjustable from 0.10 to 1.00 (pre-set at 0.95)
Over range indication: Display indication : -0L for a negative, over range, 0L for a positive over range.
Laser sighting: Wavelength : 630-670nm Output < 1mW, Class 2 (II)
Positive or negative temperature indication: Automatic (no indication for a positive
temperature) (-) sign for a negative temperature.
Display: 4 digits with LCD backlighted display.
Auto-extinction: Automatic after 7 seconds of inactivity.
High/low alarm: Flashing signal on display and beep signal with adjustable thresholds.
Power supply: Alkaline 9V battery.
Autonomy: 38h (inactive laser and backlight) 15 h (active laser and backlight)
Use temperature: From 0 to +50C.
Storage temperature: From -20C to +60C.
Relative humidity: From 10% to 90%RH in operating mode and >80%RH in storage.
Dimensions: 175x110x45mm.
Weight: 230g (included battery).
Memory: 20 temperature values with unit of measurement (C or F).
Make sure that the target is larger than the size of the laser sighting.

K thermocouple probe features
Temperature range: From -40 to +400C
Display range: From -50 to +1370C
Resolution: 0.1C
Accuracy: plus/minus 1.5% of reading plus/minus 3C
Cable length:1m

*Accuracy for an ambient temperature from 18 to 28C (with a relative humidity lower
than 80% RH)

Narrow Series Deep Groove Ball Bearings - C3 Clearance

Slightly narrower than the 6000 series with the same bore and outside diameter. Designed to withstand radial loads, withstand axial loads in both directions and operate at high speeds of rotation.

Self Aligning Bearings

With double ball rows and a spherical raceway in the outer ring, self-aligning ball bearings can compensate for installation errors or shaft misalignment. Useful for applications requiring high rotating speeds while exercising moderate radial, and moderate or low axial loading. Available in cylindrical bore or taper bore (K suffix). Clearance is standardised (ISO 5753). The values are different for cylindrical bore and tapered bore bearings (suffix K). The latter have a significantly larger clearance to allow the reduction in clearance resulting from the adapter sleeves interference fit.

Self Aligning - Plain Bore