High Speed Steel Straight Shank Spiral Flute Parallel Hand Reamer

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.



Imperial Limits of Tolerance Diameter \t Over\tUp to and Including\t High \t Low -\t0.1181 \t0.0003\t0.00010.1181\t0.2362\t 0.0004\t0.00020.2362\t0.3937 \t0.0005\t0.00020.3937\t0.7087 \t0.0006\t0.00030.7087\t1.1811 \t0.0007\t0.00041.1811\t1.9685 \t0.0008\t0.00041.9685\t3.1496 \t0.0010\t0.0005

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Taylor & Jones Spiral Flute Bridge Reamers

Have a taper lead angle of 1 in 10 on diameter and are used for reaming pairs of holes which may be out of alignment, particularly with structural steel components, i.e. when assembling pre-drilled steel plate ready for riveting. Previously known as 'Boilermakers' reamers. Manufactured to BS 328 : Part 4 : 1990.

For all dimensional specifications please refer to our catalogue.

Spiral Flute Bridge Reamers - Metric

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.