Granlund Size 1 Insert Drills

Type LB HSS Tol. h8 flute 40mm.

When combining insert drills with countersinks, the drill must break through the work piece before secondary cutting commences and must not be used for blind holes.

For all technical specifications please refer to our catalogue.

Granlund Carbide Size 1 Counterbores

Type H. Carbide K40 micrograin. Tolerance P8.

Counterbores H with a diameter of 50mm and larger are all made with a driving lip. These sizes should be used in the appropriate type M toolholder.

For further specifications please refer to our catalogue.

Granlund Size 1 Pilots

Type R Roller. c9.

When working ?dry? type R roller pilots must be lubricated. Pilots type RS must be combined with holders type AS.

For all technical specifications please refer to our catalogue.

Granlund HSS Size 1 Counterbores

Type N. HSS. Tolerence P8.

Counterbores N with a diameter of 50mm and larger are all made with a driving lip. These sizes should be used in the appropriate type M toolholder.

For further specifications please refer to our catalogue.

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

ER Collet Chucks

E4 to DIN 6499/B

Indexa-Seiki KC3 - Adaptors

Combination shank. Allows Kennedy & Clarkson throw-away milling cutters to be used with standard 16mm Weldon and screwed chucks/collets.

KC3 Combi Shank Adaptor

Allied Maxcut Indexable Drill Inserts

For a full range of Allied Maxcut Tool holders please refer to our catalogue.

For all technical and dimensional specifications please refer to our catalogue.

Inserts

Indexa-Seiki Tapping Collets

Rigid type. To suit Indexa-Seiki Rigid type tapping chucks.

For all dimensional and technical specifications please refer to our catalogue.

DIN SZ2

Kennametal Face Milling

Kennametal Dodeka™ inserts and cutters are for demanding face-milling applications in steel, stainless steel, cast iron, ductile iron, and other materials. They have been engineered to deliver higher cutting speeds and feed rates along with extended tool life. This has resulted in improved cutting performance and productivity across the most demanding of materials.

Compared to competitors' face-milling inserts, Dodeka inserts provide up to 30% more cutting performance at the same level of power consumption. At the same cutting conditions, Dodeka inserts supply up to 50% longer tool life.

With 12 cutting edges per insert, the unique Dodeka geometry generates low cutting forces, resulting in increased performance per edge. The inserts are also designed for ease of use, with a single screw for insert changing and indexing.

Dodeka™ Face Mills

Kennametal Dodeka™ Face Mills are specifically engineered to deliver consistent performance in demanding rough and finishing face milling applications!
Use less horsepower - and gain up to 30% in productivity.
Up to 50% longer tool life.
Easy-to-use - one screw enables fast, accurate indexing.
12 true cutting edges lower your cost per edge.
Run at higher speeds and feeds - with higher metal-removal rates.
Three new cutter sizes and three new geometries, including a new Wiper insert.
Engineered for applications requiring higher cutting speeds and feed rates with low cutting forces.
Ideally suited for roughing and finishing face milling applications in the General Engineering and
Automotive industries.
4.5mm depth-of-cut capability.
Available in diameters from 40 - 315mm.
Through-coolant standard.


For all technical specifications and inserts please refer to our catalogue.

Structural Steel Drill Insert Range

GEN3SYS. High performance carbide inserts for rigid applications. available in K35 (Steel grade) with dedicated high strength holders. Helical insert can provide better swarf control and hole finish.

AM200?