Allied Maxcut Series 2 and 2.5 Inserts

For all dimensional specifications please refer to our catalogue.

GEN2 T-A T-A K35 Carbide AM200 Coated

Iscar Helido Indexable Endmills and Facemills

The new HELIDO H490 ANKX rectangular inserts have 4 helical right-hand positive cutting edges. They were designed in cutting edge lengths of 9, 12 and 17 mm. Insert construction is very thick and strong; clamped into a dovetail inclined pocket which provides a very rigid clamping and has a wiper which leaves an excellent surface finish.

Due to its strong construction, unique chip deflector with positive cutting angles and excellent grade combinations, this new family features high durability, low cutting forces and long tool life. Our most advanced SUMO TEC grades ensure excellent performance and reliability.

The new HELIDO tools can be used for machining steel, stainless steel and cast iron at very high machining parameters. HELIDO"s state-of-the-art of milling insert design, enables excellent performance and extremely high productivity.

H490 - A new family of double-sided inserts with 4 helical cutting edges.

For further specification on this product please see refer to our catalogue page.

H490 E90AX...-09 Indexable End Mills

End Mills with double-sided inserts, diameter range 16-40mm.

Iscar Helido Indexable Endmills and Facemills

The new HELIDO H490 ANKX rectangular inserts have 4 helical right-hand positive cutting edges. They were designed in cutting edge lengths of 9, 12 and 17 mm. Insert construction is very thick and strong; clamped into a dovetail inclined pocket which provides a very rigid clamping and has a wiper which leaves an excellent surface finish.

Due to its strong construction, unique chip deflector with positive cutting angles and excellent grade combinations, this new family features high durability, low cutting forces and long tool life. Our most advanced SUMO TEC grades ensure excellent performance and reliability.

The new HELIDO tools can be used for machining steel, stainless steel and cast iron at very high machining parameters. HELIDO"s state-of-the-art of milling insert design, enables excellent performance and extremely high productivity.

H490 - A new family of double-sided inserts with 4 helical cutting edges.

For further specification on this product please see refer to our catalogue page.

H490 E90AX...-09 Indexable End Mills

End Mills with double-sided inserts, diameter range 16-40mm.

Allied Maxcut Series 1 and 1.5 Inserts

For all dimensional specifications please refer to our catalogue.

GEN2 T-A K20 Carbide AM200 Coated

Allied Maxcut Series 2 and 2.5 Holders

Diameter range: 24.41 to 35.05mm.

For all dimensional specifications please refer to our catalogue.

Taper Shank

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 1.0 - 7.0.
(D)11.5mm x (L)18.0mm.

ER11

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

Radial

Short B1 Right Hand

PSC and PSCa (adjustable) Collets for Plain Shank Cutters

Tru-Loc Collets are available for plain shank cutters in two different styles, PSC non adjustable and PSCa - Collets with an adjustable back-stop screw to allow more accurate & consistent cutter replacement.

For all dimensional specifications please refer to our catalogue.

PSC(a) Type

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 2.0-20.
(D)33mm x (L)40mm.

ER32

Indexa-Seiki SL - Sidelock Adaptors

For Weldon shank cutters, adaptors and tapping chucks. Manufactured to stringent quality standards.

Short Length

To DIN69871/A