Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

Radial

Long Upside Down B8 Left Hand

Granlund Carbide Size 1 Counterbores

Type WHV. For Carbide inserts. Tolerance plus/minus 0.1.

The WHV Rotatip counterbore should always be combined with type R or RS roller pilots. The shank of the holder must not be smaller than MT3.

For further specifications please refer to our catalogue.

Allied Maxcut Series Y Inserts

For all dimensional specifications please refer to our catalogue.

GEN2 T-A HSS Super Cobalt AM200 Coated

Kennametal Face Milling

Kennametal Dodeka™ inserts and cutters are for demanding face-milling applications in steel, stainless steel, cast iron, ductile iron, and other materials. They have been engineered to deliver higher cutting speeds and feed rates along with extended tool life. This has resulted in improved cutting performance and productivity across the most demanding of materials.

Compared to competitors' face-milling inserts, Dodeka inserts provide up to 30% more cutting performance at the same level of power consumption. At the same cutting conditions, Dodeka inserts supply up to 50% longer tool life.

With 12 cutting edges per insert, the unique Dodeka geometry generates low cutting forces, resulting in increased performance per edge. The inserts are also designed for ease of use, with a single screw for insert changing and indexing.

Dodeka™ Face Mills

Kennametal Dodeka™ Face Mills are specifically engineered to deliver consistent performance in demanding rough and finishing face milling applications!
Use less horsepower - and gain up to 30% in productivity.
Up to 50% longer tool life.
Easy-to-use - one screw enables fast, accurate indexing.
12 true cutting edges lower your cost per edge.
Run at higher speeds and feeds - with higher metal-removal rates.
Three new cutter sizes and three new geometries, including a new Wiper insert.
Engineered for applications requiring higher cutting speeds and feed rates with low cutting forces.
Ideally suited for roughing and finishing face milling applications in the General Engineering and
Automotive industries.
4.5mm depth-of-cut capability.
Available in diameters from 40 - 315mm.
Through-coolant standard.


For all technical specifications and inserts please refer to our catalogue.

PSC and PSCa (adjustable) Collets for Plain Shank Cutters

Tru-Loc Collets are available for plain shank cutters in two different styles, PSC non adjustable and PSCa - Collets with an adjustable back-stop screw to allow more accurate & consistent cutter replacement.

For all dimensional specifications please refer to our catalogue.

PSC Type

Granlund HSS Size 1 Counterbores

Type NA. HSS. Tolerence P8.

Counterbores NA with a diameter of 50mm and larger are all made with a driving lip. These sizes should be used in the appropriate type M toolholder.

For further specifications please refer to our catalogue.

PSC and PSCa (adjustable) Collets for Plain Shank Cutters

Tru-Loc Collets are available for plain shank cutters in two different styles, PSC non adjustable and PSCa - Collets with an adjustable back-stop screw to allow more accurate & consistent cutter replacement.

For all dimensional specifications please refer to our catalogue.

PSC(a) Type

Indexa-Seiki? ER Collets

Indexa-Seiki? ER collets are the most versatile toolholding system for any operation that utilises a round shank cutting tool in a machining centre. Typical applications include drilling, milling, tapping, reaming and boring.

When Indexa-Seiki? ER collets are used with round shank cutting tools the collet chucks centralise the cutting tool and if all the ER system components have been maintained correctly, this should result in increased tool life, higher feed rates, better work piece accuracy and enhanced work piece finish.

ER Collet Set

Indexa-Seiki? ER Collets are available in the in a range of sizes to maximise efficiency in most applications, they are manufactured from hardened and tempered high alloy steel. All supplied in hardwearing bench cases with protective foam inserts.

Conform to DIN 6499.
Up to 10.0mm - 0.015mm TIR.
11.0 to 18.0mm ? 0.015 to 0.020mm TIR.
19.0 to 26.0mm ? 0.015 to 0.020mm TIR.

For all technical and dimensional specifications please refer to our catalogue.

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 3.0-26.
(D)41mm x (L)46mm.

ER40

Granlund HSS Size 1 Countersinks

Type T. HSS. Tolerance x9 90.

Countersink T with a diameter 50mm and larger are made with a driving lip. These sizes should be used in the appropriate type M holder.

For further specifications please refer to our catalogue.