Rotabroach Mini Cutter Accessories

To suit Rotabroach Mini Cutters.

Pilots

Rotabroach Mini Cutters

For perfect holes in sheet metal, pipes & plastic. Cut clean, burr-free holes in seconds with new Roatabroach Mini-Cutters, the professional solution to holemaking in sheet metal, pipes and plastics. Mini-Cutters produce holes by removing a 'disc' of metal and have precision ground teeth and flutes to rapidly remove waste material, so they are fast, smooth and highly accurate. Now they come with a new and more aggressive tooth geometry to give high higher performance and longer cutting life on stainless steel and other difficult materials. No toolbox is complete without Mini-Cutters for clean, precise and effortless holecutting every time. Over 3 times faster than twist drills Mini-Cutters have multiple teeth and an annular
cutting action with no 'dead centre' area as with a twist drill. It means that less pressure is required to make the hole, so there is less risk of deforming sheet metal. This highly efficient cutting action also ensures minimal burring on breakthrough, reducing or completely eliminating the need for additional finishing work. Last up to 300 times longer than hole saws Holesaws have stamped teeth which only remove
small particles of metal with each revolution whereas Mini-Cutters are precision ground cutting instruments which slice their way through sheet metal without leaving burrs or jagged edges. Because they are made from M2 High Speed Steel,
they retain their sharpness to give a longer, more reliable cutting life over thousands of holes.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Dronco Diamond Cutting Blades

Dry or wet cutting diamond disc which is a laser-welded all-purpose segmented disc designed to cut construction-site materials. For use on concrete, exposed aggregate concrete, border stones.

LT46 Diamond Cutting Discs

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Dronco Diamond Cutting Blades

Dry cutting diamond disc which is sintered and segmented designed to cut construction-site materials with a good price/performance ratio. For use on all kinds of construction site material.

ST7

Kennedy® Tie Cord Bonnet Support Pads

High quality 23mm foam pads with rigid back plates. For use with all tie cord bonnets. Bonnets supplied separately. Max 2500rpm. (125mm and 150mm pads are dual purpose - also for use with Velcro bonnets or foams).

Bonnet diameters available: 125mm, 150mm, 180mm, and 200/225mm.
Thread sizes: M14 x 2 and 5/8" UNC.

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Velcro Backed Sanding Discs

No spanners required. 100% of disc can be used, material removal rate is therefore increased. Can be repeatedly removed and re-applied. Silicon carbide abrasive epecially suitable for automotive body preparation prior to spraying and for cutting back two-pack paint finishes. Can be used wet or dry.



75mm (3"). Pack 25

09273

• 230v (13amp) supply
• Adjustable 38,841 - 63,500 BTU/hr
(11.4 - 18.6kW) heat output
• Maximum 426m3 (15,044 cu.ft)
approx. heating area
• Low 0.744 - 1.213kg/hr average gas consumption
• Rugged non-corrosive stainless steel casing for tough daily use
• Highly portable
• Made in Italy
• 2 Year Warranty
BADGES: Made in Italy, NEW, 2 year warranty, Stainless Steel, 13amp supply