Heavy-Duty Vertical Bandsaws

Heavy-Duty suitable for continuous use. High quality electrics and limit switches to blade wheelcovers make safe to use and conform to CE. Air pipe keeps the visibility clear near the cutting edge

Standard Accessories:
Saw blade butt welder with integrated annealing unit.
Blade shear, grinder & built-in blade and tyre cleaning brush.
Lo-volt light.
Set of tools.
Instruction manual and parts list.
Rip fence for straight, repeated cutting and is easily adjustable for varied size.
Mitre protractor for angular cutting.

Model KV60 60? Throat 1-631-300

Cutting blade to column: 600mm.
Capacity max. work height: 300mm.
Table size: 600x500mm.
Table extension: 220x500mm.
Table inclination (4 ways): 15.
Blade length: 3970mm.
Max width: 16mm.
Blade speeds stepless: Low 15-55m/min, High 96-390m/min.
Butt welder capacity: 2.4KVA 3-16mm.
Drive motor: 1.5kW.
Weight: 700kgs.

Model D420 x 1000 420mm Swing x 1000mmDBC 3ph 0340-1160

Induction hardened and precision ground heavily ribbed prismatic bed. Substructure and lathe bed made from a single block of Meehanite cast iron. Camlock spindle nose D1-6. Oil-quenched hardened work spindle bedded in two readjustable precision taper roller bearings. Guaranteed concentricity precision of the spindle nose 0.015mm. Smooth running work spindle gearwheels hardened and precision ground. Leadscrew and feed shaft drive easily switchable via oil quenched feed gear. Adjustable safety coupling of the feed shaft. The tailstock may be shifted plus/minus for taper turning. Right - left - hand rotation can be switched with the help of the indexing spindle. Emergency stop mushroom switch, lockable main switch. Removable gap bed. Adjustable dial of the threading gauge. Mechanical foot spindle brake. Manufactured to DIN 8606 (toolmakers precision).

Standard accessories:
200mm 3 jaw chuck, 250mm 4 jaw chuck, 350mm face plate, steady rest, follow rest, coolant system, rear splash guard, spindle brake, 2-step drive motor, electrically interlocked chuck guard, turret limit stop with fine adjustment acting as end stop on lathe saddle, machine lamp, threading gauge, operating tools.

Specifications:
Between centres: 1000mm.
Centre height: 210mm.
Max.turning diameter: 420mm.
Max turning diameter over saddle: 255mm.
Max turning diameter over gap: 590mm.
Bed width: 250mm.
Spindle hole: 52mm.
Spindle taper: 6MT.
Tailstock taper: 4MT.
Spindle: D1-6.
No of spindle speeds: 16.
Spindle speeds: 45-1800rpm.
Longitudinal feeds: 0.05-1.7mm/rev.
Cross feeds: 0.025-0.85mm/rev.
Pitch metric (39): 0.2-14mm.
Pitch inch (45): 2-72tpi.
Modular thread (18): 0.3-3.5mp.
Trapezoid thread (21): 8-44dp.
Top slide travel: 140mm.
Cross slide travel: 230mm.
Sleeve travel: 120mm.
Max. Tool shank: 20mm.
Main motor power: 4.5kW.
Coolant pump: 0.1kW.
Size (LxWxH): 195x91x135cms.
Weight: 1570kgs.

Excel Heavy-Duty Bandsaw

Micro alignment of blade through ball bearings. Dovetail slide with take up gib. Rapid approach vice. Adjustable hydraulic feed. Automatic cut off. Variable Speed: No belt change. No time wasting. Speeds up production.

Standard Accessories:
Coolant pump & accessories.
Instruction manual.

Optional Accessories:
Single roller stand 1-625-994 MSR4 4 Roller adj. stand 0335-7610.

Specifications:
Maximum capacity:
@ 90 - round 250mm, square 250 x 250mm, rectangular (H x W): 250 x 415mm.
@ 45 - round 190mm, square 190 x 190mm, rectangular (H x W): 250 x 190mm.
Vice capacity: 450mm.
Blade size: 3300 x 27 x 0.9mm.
Blade speed - stepless: 25-75m/min.
Mitre cut: 45.
Motor: 2hp.
Weight: 325kg.
Dimensions (L x W x H): 1750 x 575 x 1120mm.

Geared Drive Bandsaws

Convincing arguments: quality, efficiency and price. User-friendly safety switch according to IP54 with under voltage release and protective motor switch. Three blade speeds via gear shifting mechanism. Robust cast iron design. Lowering using hydraulic system with continuous adjustment. Coolant system supplied as standard. Ball bearing 5 point blade guide. Quick action vice. Automatic limit stop. Chip brush.

Standard Accessories:
Bi-metal blade.
Hydraulic counter pressure cylinder.
Machine sub structure.
Material limit stop.
Quick action vice.
Coolant equipment.

Models S181G: 0330-0176 240V 1PH / 0330-0182 415V 3PH

Specifications:
Maximum capacity details:
Cutting range at 0 (Round): 180mm.
Cutting range at 0 (Square): 180 x 240mm / 65 x 300mm.
Cutting range at 45 (Round): 110mm.
Cutting range at 45 (Square): 170 x 110mm.
Blade speed: 39/66/82 m/min.
Blade size: 2362 x 19mm.
Dimensions: 1275 x 450 x 1100mm.
Weight: 130kg.
Motor power: 750w.

Model D420 x 1500 420mm Swing x 1500mmDBC 3ph 0340-1165

Induction hardened and precision ground heavily ribbed prismatic bed. Substructure and lathe bed made from a single block of Meehanite cast iron. Camlock spindle nose D1-6. Oil-quenched hardened work spindle bedded in two readjustable precision taper roller bearings. Guaranteed concentricity precision of the spindle nose 0.015mm. Smooth running work spindle gearwheels hardened and precision ground. Leadscrew and feed shaft drive easily switchable via oil quenched feed gear. Adjustable safety coupling of the feed shaft. The tailstock may be shifted plus/minus for taper turning. Right - left - hand rotation can be switched with the help of the indexing spindle. Emergency stop mushroom switch, lockable main switch. Removable gap bed. Adjustable dial of the threading gauge. Mechanical foot spindle brake. Manufactured to DIN 8606 (toolmakers precision).

Standard accessories:
200mm 3 jaw chuck, 250mm 4 jaw chuck, 350mm face plate, steady rest, follow rest, coolant system, rear splash guard, spindle brake, 2-step drive motor, electrically interlocked chuck guard, turret limit stop with fine adjustment acting as end stop on lathe saddle, machine lamp, threading gauge, operating tools.

Specifications:
Between centres: 1500mm.
Centre height: 210mm.
Max.turning diameter: 420mm.
Max turning diameter over saddle: 255mm.
Max turning diameter over gap: 590mm.
Bed width: 250mm.
Spindle hole: 52mm.
Spindle taper: 6MT.
Tailstock taper: 4MT.
Spindle: D1-6.
No of spindle speeds: 16.
Spindle speeds: 45-1800rpm.
Longitudinal feeds: 0.05-1.7mm/rev.
Cross feeds: 0.025-0.85mm/rev.
Pitch metric (39): 0.2-14mm.
Pitch inch (45): 2-72 TPI
Modular thread (18): 0.3-3.5 MP
Trapezoid thread (21): 8-44 DP.
Top slide travel: 140mm.
Cross slide travel: 230mm.
Sleeve travel: 120mm.
Max. Tool shank: 20mm.
Main motor power: 4.5kW.
Coolant pump: 0.1kW.
Size (LxWxH): 245x91x135cms.
Weight: 1950kg.

Heavy-Duty Hydraulic Hacksaw

KP200
Complete hydraulic system. Infinitely variable saw feed pressure control. Complete electric components with motor protection. Recalculating coolant system. Adjustable material length stop. Clamping device for short ends. Equalising bar for jaws. Nesting fixture for multiple sawing of stacked bars, small rounds and tubing. Material support stand. One saw blade ready for cutting. One set of necessary tools and tool box. One grease gun. Instruction manual and parts list.

Specifications:
90 max.: 200mm.
Capacity: 190 x 200mm.
45 max.: 90mm.
Capacity: 190 x 90mm.
Stroke length: 120mm.
Strokes: 110, 140/min.
Blade size: 350 x 32mm.
Main motor: 4P, 1HP.
Size (L x W x H): 120 x 51 x 79cms.
Weight: 270kg.

Heavy-Duty Vertical Bandsaws

Heavy-Duty suitable for continuous use. High quality electrics and limit switches to blade wheelcovers make safe to use and conform to CE. Air pipe keeps the visibility clear near the cutting edge

Standard Accessories:
Saw blade butt welder with integrated annealing unit.
Blade shear, grinder & built-in blade and tyre cleaning brush.
Lo-volt light.
Set of tools.
Instruction manual and parts list.
Rip fence for straight, repeated cutting and is easily adjustable for varied size.
Mitre protractor for angular cutting.

Model KV100 100? Throat 1-631-400

Cutting blade to column: 1000mm.
Capacity max. work height: 300mm.
Table size: 600x500mm.
Table extension: 450x500mm.
Table inclination (4 ways): 15.
Blade length: 4540mm.
Max width: 16mm.
Blade speeds stepless: Low 15-55m/min, High 96-390m/min.
Butt welder capacity: 2.4KVA 3-16mm.
Drive motor: 1.5kW.
Weight: 800kgs.

Model D330x1000, 0340-1007 3ph, 0340-1006 1ph

Rigid heavily ribbed, hardened and precision ground cast iron bed with V guideways. Camlock spindle nose D1-4. Hardened oil running headstock spindle with high precision, realignable tapered bearings. Guaranteed spindle nose runout less than 0.015mm. Closed quick action feed and screw cutting gears running in oil bath. Simultaneous engagement of lead screw & power feed levers is prevented by interlocking. Adjustable slip clutch of lead screw. Forward/reverse spindle switch. Safety switch with no-volt release, emergency stop and motor protection. Foot brake. Gap bed. Manufactured to DIN 8606 (Toolmakers Precision).

Specifications:
Centre height: 165mm.
Max swing over bed: 330mm.
Max swing over saddle: 198mm.
Max swing in gap: 476mm.
Length of gap: 115mm.
Distance between centres: 1000mm.
Width of bed: 187mm.
Spindle bore: 38mm.
Spindle nose: D1-4.
Spindle taper: MT 5.
Tailstock taper: MT 3.
No of spindle speeds: 8.
Range of spindle speeds: 70?2000rpm.
Leadscrew dia/pitch: 22mm, 3mm.
Cross feed: 0.033 ? 0.933mm/rev.
Longitudinal feed: 0.097 ? 2.713mm/rev.
Metric threads: 0.4 ? 7mm.
Imperial threads: 4 ? 56tpi.
Diametral threads: 8 ? 120dp.
Module threads: 0.2 ? 3.5mp.
Top slide travel: 85mm.
Cross slide travel: 170mm.
Motor power: 1.5kW.
Tool section: 16mm.
Size (LxWxH): 193 x 75 x 151cm.
Net weight: 600kg.

Model D330x1000, 0340-1007 3ph, 0340-1006 1ph

Rigid heavily ribbed, hardened and precision ground cast iron bed with V guideways. Camlock spindle nose D1-4. Hardened oil running headstock spindle with high precision, realignable tapered bearings. Guaranteed spindle nose runout less than 0.015mm. Closed quick action feed and screw cutting gears running in oil bath. Simultaneous engagement of lead screw & power feed levers is prevented by interlocking. Adjustable slip clutch of lead screw. Forward/reverse spindle switch. Safety switch with no-volt release, emergency stop and motor protection. Foot brake. Gap bed. Manufactured to DIN 8606 (Toolmakers Precision).

Specifications:
Centre height: 165mm.
Max swing over bed: 330mm.
Max swing over saddle: 198mm.
Max swing in gap: 476mm.
Length of gap: 115mm.
Distance between centres: 1000mm.
Width of bed: 187mm.
Spindle bore: 38mm.
Spindle nose: D1-4.
Spindle taper: MT 5.
Tailstock taper: MT 3.
No of spindle speeds: 8.
Range of spindle speeds: 70?2000rpm.
Leadscrew dia/pitch: 22mm, 3mm.
Cross feed: 0.033 ? 0.933mm/rev.
Longitudinal feed: 0.097 ? 2.713mm/rev.
Metric threads: 0.4 ? 7mm.
Imperial threads: 4 ? 56tpi.
Diametral threads: 8 ? 120dp.
Module threads: 0.2 ? 3.5mp.
Top slide travel: 85mm.
Cross slide travel: 170mm.
Motor power: 1.5kW.
Tool section: 16mm.
Size (LxWxH): 193 x 75 x 151cm.
Net weight: 600kg.

Heavy-Duty Vertical Bandsaws

Heavy-Duty suitable for continuous use. High quality electrics and limit switches to blade wheelcovers make safe to use and conform to CE. Air pipe keeps the visibility clear near the cutting edge

Standard Accessories:
Saw blade butt welder with integrated annealing unit.
Blade shear, grinder & built-in blade and tyre cleaning brush.
Lo-volt light.
Set of tools.
Instruction manual and parts list.
Rip fence for straight, repeated cutting and is easily adjustable for varied size.
Mitre protractor for angular cutting.

Model KV50 20? Throat 1-631-200

Cutting blade to column: 520mm.
Capacity max. work height: 310mm.
Table size: 600x500mm.
Table inclination (4 ways): 15.
Blade length: 3880mm.
Max width: 16mm.
Blade speeds stepless: Low 15-55m/min, High 96-390m/min.
Butt welder capacity: 2.4KVA 3-16mm.
Drive motor: 1.5kW.
Weight: 500kgs.