Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Brass Wingback Elbow

This fitting is made of the following components:-

The body is produced in brass
'O'Rings are nitrile rubber
The collet is produced in acetal copolymer with stainless steel teeth

SMC Union Y-Connectors

KQ2U
Union Y-connectors. Colour: white.
KQ2U04-00: Tube O.D. 4mm.
KQ2U06-00: Tube O.D. 6mm.
KQ2U08-00: Tube O.D. 8mm.
KQ2U010-00: Tube O.D. 10mm.
KQ2U012-00: Tube O.D. 12mm.
KQ2U016-00: Tube O.D. 16mm.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Connector to Male Parallel

Push-Fit Pneumatic Fittings

Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer.
Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: - 0.9 bar min to + 10 bar max.
Temp range: - 20C min to + 70C max.
Tube suitability: nylon, polyurethane.

KQ2H04-01S: Tube O.D. 4mm. R 1/8.
KQ2H04-02S: Tube O.D. 4mm. R 1/4.
KQ2H06-01S: Tube O.D. 4mm. R 1/8.
KQ2H06-02S: Tube O.D. 6mm. R 1/4.
KQ2H06-03S: Tube O.D. 6mm. R 3/8.
KQ2H08-01S: Tube O.D. 8mm. R 1/8.
KQ2H08-02S: Tube O.D. 8mm. R 1/4.
KQ2H08-03S: Tube O.D. 8mm. R 3/8.
KQ2H10-01S: Tube O.D. 10mm. R 1/8.
KQ2H10-02S: Tube O.D. 10mm. R 1/4.
KQ2H10-03S: Tube O.D. 10mm. R 3/8.
KQ2H10-04S: Tube O.D. 10mm. R 1/2.
KQ2H12-02S: Tube O.D. 12mm. R 1/4.
KQ2H12-03S: Tube O.D. 12mm. R 3/8.
KQ2H12-04S: Tube O.D. 12mm. R 1/2.
KQ2H16-03S: Tube O.D. 16mm. R 3/8.
KQ2H16-04S: Tube O.D. 16mm. R 1/2.

One Touch Male Connectors

Series 1000 Rapid Fittings for Plastic Tubes

They can be used with rigid PA tubes. A locking nut is provided and can be tightened both manually and with a spanner. The special shape of the guiding cone ensures that the tube cannot be accidentally cut.
General data:
Materials body and nut: nickel-plated brass; O-ring: NBR; thread seals: PTFE, PA, AL
Threads GAS, conical ISO 7 (BSPT) GAS, cylindrical ISO 228 (BSP)

Series 1541 Swivel Elbow Sprint

Elbow Type

AS series in line speed controllers minimise installation time and cost as they reduce the mounting height and enable compact machinery design. The number of needle rotations has been increased from 8 to 10 turns to permit easy control at low speeds. Applicable tube material nylon, soft nylon and polyurethane tubing.
Operating pressure: 1MPa max.

Camozzi Straight Stem Couplings

6950
Super-rapid fittings for plastic tubes. Push-in fitting straight stem coupling.
Available in:
10mm, overall length 46mm.
12mm, overall length 48mm.

Push-Fit Pneumatic Fittings

Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer.
Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: - 0.9 bar min to + 10 bar max.
Temp range: - 20C min to + 70C max.
Tube suitability: nylon, polyurethane.

KQ2H04-01S: Tube O.D. 4mm. R 1/8.
KQ2H04-02S: Tube O.D. 4mm. R 1/4.
KQ2H06-01S: Tube O.D. 4mm. R 1/8.
KQ2H06-02S: Tube O.D. 6mm. R 1/4.
KQ2H06-03S: Tube O.D. 6mm. R 3/8.
KQ2H08-01S: Tube O.D. 8mm. R 1/8.
KQ2H08-02S: Tube O.D. 8mm. R 1/4.
KQ2H08-03S: Tube O.D. 8mm. R 3/8.
KQ2H10-01S: Tube O.D. 10mm. R 1/8.
KQ2H10-02S: Tube O.D. 10mm. R 1/4.
KQ2H10-03S: Tube O.D. 10mm. R 3/8.
KQ2H10-04S: Tube O.D. 10mm. R 1/2.
KQ2H12-02S: Tube O.D. 12mm. R 1/4.
KQ2H12-03S: Tube O.D. 12mm. R 3/8.
KQ2H12-04S: Tube O.D. 12mm. R 1/2.
KQ2H16-03S: Tube O.D. 16mm. R 3/8.
KQ2H16-04S: Tube O.D. 16mm. R 1/2.

Male Elbow Connectors

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

QR1-RPN Series Straight Pneumatic Fitting

Standard metric M5-G 1/2 straight push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.

Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Reducing Tee

Connects plain pipe end to end and smaller diameter pipe at 90.