Rexroth Push-In Connectors

QR1-RAS Series
Push-in plastic fittings with external thread for compressed air hoses.
Available in threads:
G1/8 x 6mm diameter.
G1/8 x 8mm diameter.
G1/4 x 6mm diameter.
G1/4 x 8mm diameter.

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

2080 Series

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

4040 Series

PCL Airline ?Vertex? Couplings

As 'Standard' type above but with slim profile, double locking action and additional collar to prohibit dirt ingress. Designed for trailing hoses.

Male Threaded

1/4" BSPT.

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Equal Straight Connectors

Connects plain pipe end to end.

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

2050 Series

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.



3060 Series

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Elbow Reducer to Stem

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Tee

SMC Self-Align Tube Fitting Male Connector

Series H
Compression fitting.
H06-02:
Tube O.D. 6mm.
Thread: R1/4.