Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Shielded type:

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Gilkes Submersible Pumps

Submersible pumps for drainage, de-watering and general transfer of both clean and dirty liquids. AISI304 stainless steel housing and impeller. 230V 50Hz single phase.
Motors are 0.25 to 2.25kW and are all IP68.
Max. liquid temperature 40°C.
Max immersion
depth 5m.
Solid size: 7 - 20mm.
Power cable length minimum 5m.
Available with or without the float switch.
Applications:
• Emptying of sump pits, rainwater tanks.
• Irrigation
• Emergency removal of flood waters in basements
• Transfer duties for clear, sandy and muddy liquids
• Residential and industrial waste water pumping
• Sewage treatment and disposal
• Industrial effluent plants


Image for illustration
purposes only.

Titan 2XL Submersible Pump in Stainless Steel

Link-Belt Connecting Links

Other sizes from 5/16" up to 2" pitch are also available from stock. Please ask for details

Simplex Roller Chain American Standard

Simplex Chain

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Table Top Slat Chain

A complete range of table top chains and sprockets in steel, stainless steel and molded thermoplastics. These are manufactured specifically for a conveying applications.
Some table top chains have been standardised between manufacturers. We show below the most popular ranges but with many specialty attachments and options available on table top chain, please contact your local service centre to assist in identifying and recommending the right table top chain for your application.

880 Series - Side Flexing Chain

Material: Ultra performance acetal resin
Length: 10?.

SNR Deep Groove Ball Bearings

Open type without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

Open Deep Groove Ball Bearings

Dimensions to ISO15

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.

SK High Power Wedge Belts

SK wedge belts offer significant performance advantages with up to 97% drive efficiency with extended belt life and easier fitting.
S=C Plus length tolerance* Belts are automatically length matched to very tight tolerances and so require no matching, are easier to fit and run more efficiently in sets.
Example: SPC 5000 tolerance range = +/-2mm compared to DIN standard/other manufacturers = +/-50mm
Advanced manufacturing techniques like our rotational curing process mean that our SK belts are less prone to fatigue and absorb less power in wrapping around the pulley, resulting in improved drive efficiency and longer belt life.
*applies to belts over 1160mm length. Consult catalogue for details.
Dimensions: 487 to 12500mm.
Standard range further sizes on request.

Belt Section 17/B (SPB/17)

SNR Shaft Seals & Adaptors

SNC bearing housings can be used for both fixed and floating bearing arrangements. Locating rings enable the bearing to be fixed in place axially. The width of the locating rings is adapted to the bearing being used. To secure the bearings, two locating rings per housing are required.

Locating Rings