Elastomeric Couplings

Rexnord Viva Couplings feature a two-piece flex element design allows for simple replacement without disturbing hubs or moving and realigning connected equipment. Tough polyurethane material is bonded to a corrosion resistant coated shoe, eliminating the need for mechanical clamping hardware. Adhesive coated high strength carbon steel shoe resists corrosion. Easily aligned reversible hubs accommodate multiple shaft gaps. Hubs are available in rough bore, custom bore, or bushed designs. Optional hub materials are available. High grade cap screws are provided with self locking nylon thread patches. Stainless steel cap screws are also available. Torsionally soft polyurethane element cushions shock loads, accommodates unavoidable misalignment and is compatible with most environments. ?V? notch design directs stress concentration away from the bond area providing a uniform failure area for overload protection if required.

Viva Taper Bore Hubs

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Inner Ring and Outer Ring is without Ribs

SK High Power Wedge Belts

SK wedge belts offer significant performance advantages with up to 97% drive efficiency with extended belt life and easier fitting.
S=C Plus length tolerance* Belts are automatically length matched to very tight tolerances and so require no matching, are easier to fit and run more efficiently in sets.
Example: SPC 5000 tolerance range = +/-2mm compared to DIN standard/other manufacturers = +/-50mm
Advanced manufacturing techniques like our rotational curing process mean that our SK belts are less prone to fatigue and absorb less power in wrapping around the pulley, resulting in improved drive efficiency and longer belt life.
*applies to belts over 1160mm length. Consult catalogue for details.
Dimensions: 487 to 12500mm.
Standard range further sizes on request.

Belt Section 13/A (SPA/13)

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Open Type

Without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

VB Classical V-Belt

V-Belts to BS3790, DIN2215 and ISO 4184.



Belt Section 13A (SPA/13)

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

V-Grooved Pulleys for Taper Bushes

Grooves to ISO/BS/DIN 2211.

Belt Section 17/B (SPB/17)

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.

V-Grooved Pulleys for Taper Bushes

Grooves to ISO/BS/DIN 2211.

Belt Section 17/B (SPB/17)