Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 13/A (SPA/13)

Max Width (b1) 13mm, Height (h)8mm.

Adapter Sleeves

Adaptor sleeves are commonly used for locating tapererd bored bearing and securing them to a shaft. They can be accurately positioned and dismounted. By using in conjuction with SNR feeler gauges accurate radial clearances will be achieved.

W22 3 Phase Motors - A Revolution in Energy Efficiency

The W22 is a range of three-phase induction motors which reduces energy consumption, noise, vibration and cost of ownership.With an aerodynamic frame, redesigned cooling system, unique WISE insulation system and new WSeal 'V' Ring with double lip and metallic cap, the W22 range of motors is quieter, more reliable, easier to maintain and more cost effective.

Cast Iron IE3 Multi-Voltage Three Phase Motors

Cast iron frame motors - IE3 (Premium Efficiency) three-phase motors. These motors exceed the IE3 New European Minimum Energy Performance Standard (EU MEPS). Thermisters fitted as standard in frame 160 and above. IP55 protection as standard (up to IP66 on request).

Self Aligning Bearings

With double ball rows and a spherical raceway in the outer ring, self-aligning ball bearings can compensate for installation errors or shaft misalignment. Useful for applications requiring high rotating speeds while exercising moderate radial, and moderate or low axial loading. Available in cylindrical bore or taper bore (K suffix). Clearance is standardised (ISO 5753). The values are different for cylindrical bore and tapered bore bearings (suffix K). The latter have a significantly larger clearance to allow the reduction in clearance resulting from the adapter sleeves interference fit.

Self Aligning - Taper Bore

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Open type:

Without seals to allow for the free circulation of either oil or grease.

Angular Contact Bearings - Double Row

Double-row angular-contact ball bearings accept axial loads in both directions and can be used singly, as dual bearing units.? withstand axial loads in both directions? accept relatively high speeds of rotationThe construction of these bearings limits them to very small misalignment values, in the range of 0.06.

Series 32...A, 33...A

Contact angle 25, no filling slots and can accept axial loads in both directions. These bearings have synthetic material cages.

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 22/C (SPC/22)

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.