Super X-Power V-Belt

Moulded Cogged Raw Edge Wedge Belts



Belt Section 10/Z (SPZ/10)

Self Aligning Bearings

With double ball rows and a spherical raceway in the outer ring, self-aligning ball bearings can compensate for installation errors or shaft misalignment. Useful for applications requiring high rotating speeds while exercising moderate radial, and moderate or low axial loading. Available in cylindrical bore or taper bore (K suffix). Clearance is standardised (ISO 5753). The values are different for cylindrical bore and tapered bore bearings (suffix K). The latter have a significantly larger clearance to allow the reduction in clearance resulting from the adapter sleeves interference fit.

Self Aligning - Plain Bore

VB Classical V-Belt

V-Belts to BS3790, DIN2215 and ISO 4184.



Belt Section 13A (SPA/13)

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Roller Chain

Renold Blue Box chain with their unique control over pin/bush contact, ensures that little initial chain adjustment is therefore required. Renold Blue Box roller chain is highly fatigue resistant with breaking loads exceed the minimum requirements of the international standards.
The specification of Renold chain has evolved from decades of design, test and application experience which delivers product reliability and consistency. Other sizes from 5/16” to 2” pitch are also available please ask for details.
Conforms to: DIN8187/IS606

Simplex Chain

Gilkes Submersible Pumps

Submersible pumps for drainage, de-watering and general transfer of both clean and dirty liquids. AISI304 stainless steel housing and impeller. 230V 50Hz single phase.
Motors are 0.25 to 2.25kW and are all IP68.
Max. liquid temperature 40°C.
Max immersion
depth 5m.
Solid size: 7 - 20mm.
Power cable length minimum 5m.
Available with or without the float switch.
Applications:
• Emptying of sump pits, rainwater tanks.
• Irrigation
• Emergency removal of flood waters in basements
• Transfer duties for clear, sandy and muddy liquids
• Residential and industrial waste water pumping
• Sewage treatment and disposal
• Industrial effluent plants


Image for illustration
purposes only.

Titan 2GL Submersible Pump in Cast Iron

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 13/A (SPA/13)

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 10/Z (SPZ/10)

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.