Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Shielded Type

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Optibelt Timing Belts

Optibelt?s Omega timing belts give long lasting
high performance with a number of advantages:
Reduced noise.
Runs in both standard HTD and RPP pulleys.
High efficiency - up to 98%.
Maintenance-free.

Omega High Quality Timing Belts

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Angular Contact Bearings - Double Row

Double-row angular-contact ball bearings accept axial loads in both directions and can be used singly, as dual bearing units.? withstand axial loads in both directions? accept relatively high speeds of rotationThe construction of these bearings limits them to very small misalignment values, in the range of 0.06.

Series 32...B, 33...B

Contact angle 32, with filling slots and accept axial loads (higher loads than Type A) in a predominant direction. Cage in pressed steel, synthetic material or machined brass.

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Open type:

Without seals to allow for the free circulation of either oil or grease.

Elastomeric Couplings

Rexnord Omega couplings are non-lubricated, material-flexing couplings utilising a specially formulated polyurethane material engineered for maximum durability, strength and fatigue resistance. The flex element is designed to split in half, allowing simplified assembly and disassembly. Interchangeable hubs allow for reduced inventory. High misalignment capacity accommodates unavoidable misalignment with low reactionary forces. Torsionally soft flex element cushions shock loads and vibration extending equipment life. Polyurethane flex element does not require lubrication. Polyurethane-to-metal bond eliminates assembly and slippage problems associated with mechanically clamped designs.

Omega Close Coupled Elements

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 22/C (SPC/22)

RexPro Carbon Steel Chain

With RexPro, Rexnord set a new standard for quality chains. The RexPro chain is the result of further developing the
Rexnord high performance chain. Over a timespan of four years the combination of selected steels, optimised manufacturing and the RexPro lubrication have all achieved these outstanding product characteristics.

American Standard Roller Chain - DIN8188/ISO 606 (ANSI B29.1).

Duplex Chain

Self Aligning Bearings

With double ball rows and a spherical raceway in the outer ring, self-aligning ball bearings can compensate for installation errors or shaft misalignment. Useful for applications requiring high rotating speeds while exercising moderate radial, and moderate or low axial loading. Available in cylindrical bore or taper bore (K suffix). Clearance is standardised (ISO 5753). The values are different for cylindrical bore and tapered bore bearings (suffix K). The latter have a significantly larger clearance to allow the reduction in clearance resulting from the adapter sleeves interference fit.

Self Aligning - Taper Bore