Optibelt Timing Belts

Optibelt?s Alpha timing belts are manufactured from high grade polyurethane with steel reinforcing cords.

High precision profile for good repeatability.
Very low stretch.
Resistant to many oils and chemicals.
Wide and flexible range.

Alpha Polyurethane Timing Belts

AT-Pitch Range - AT5, AT10

Elastomeric Couplings

Rexnord Viva Couplings feature a two-piece flex element design allows for simple replacement without disturbing hubs or moving and realigning connected equipment. Tough polyurethane material is bonded to a corrosion resistant coated shoe, eliminating the need for mechanical clamping hardware. Adhesive coated high strength carbon steel shoe resists corrosion. Easily aligned reversible hubs accommodate multiple shaft gaps. Hubs are available in rough bore, custom bore, or bushed designs. Optional hub materials are available. High grade cap screws are provided with self locking nylon thread patches. Stainless steel cap screws are also available. Torsionally soft polyurethane element cushions shock loads, accommodates unavoidable misalignment and is compatible with most environments. ?V? notch design directs stress concentration away from the bond area providing a uniform failure area for overload protection if required.

Viva Taper Bore Hubs

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.
Belt Section 13/A (SPA/13)

Conti-V Ultraflex V-Belts

Super X-Power V-Belt

Moulded Cogged Raw Edge Wedge Belts



Belt Section 13/A (SPA/13)

SNR Deep Groove Ball Bearings

Open type without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

Open Deep Groove Ball Bearings

Dimensions to ISO15

VB Classical V-Belt

V-Belts to BS3790, DIN2215 and ISO 4184.



Belt Section 10/Z (SPZ/10)

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Gilkes Submersible Pumps

Submersible pumps for drainage, de-watering and general transfer of both clean and dirty liquids. AISI304 stainless steel housing and impeller. 230V 50Hz single phase.
Motors are 0.25 to 2.25kW and are all IP68.
Max. liquid temperature 40°C.
Max immersion
depth 5m.
Solid size: 7 - 20mm.
Power cable length minimum 5m.
Available with or without the float switch.
Applications:
• Emptying of sump pits, rainwater tanks.
• Irrigation
• Emergency removal of flood waters in basements
• Transfer duties for clear, sandy and muddy liquids
• Residential and industrial waste water pumping
• Sewage treatment and disposal
• Industrial effluent plants


Image for illustration
purposes only.

Titan 2XL Submersible Pump in Stainless Steel

Continental Contitech V-Belts

Heavy-duty cogged raw edge V-belts, DIN 7753. Moderately oil-resistant. Resistant to temperature from -30 to 80C. Electrically conductive (antistatic) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Elastomeric Couplings

Rexnord Viva Couplings feature a two-piece flex element design allows for simple replacement without disturbing hubs or moving and realigning connected equipment. Tough polyurethane material is bonded to a corrosion resistant coated shoe, eliminating the need for mechanical clamping hardware. Adhesive coated high strength carbon steel shoe resists corrosion. Easily aligned reversible hubs accommodate multiple shaft gaps. Hubs are available in rough bore, custom bore, or bushed designs. Optional hub materials are available. High grade cap screws are provided with self locking nylon thread patches. Stainless steel cap screws are also available. Torsionally soft polyurethane element cushions shock loads, accommodates unavoidable misalignment and is compatible with most environments. ?V? notch design directs stress concentration away from the bond area providing a uniform failure area for overload protection if required.

Viva Taper Bore Hubs