Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Outer Ring and Inner Ring is without Ribs

Tab Washers

Tab washers are used for securing KM series lock nuts. They have an inner tab for location on the adaptor sleeve. One of the external tabs is bent over a slot when used wit the
KM series lock nuts.

SNR Deep Groove Ball Bearings

With Shields

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Plummer Blocks - Light Series - SL Type

Cast iron self lube unit plummer blocks.
Light series. With two slotted holes for fixing.

SNR Deep Groove Ball Bearings

With Shields

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

SNR Pillow Block Housings

The housings are produced from grey cast iron in compliance with DIN EN 1561 and external surface painted RAL 5010 - Gentian Blue) the machined surfaces are treated with an anti-corrosion agent. Threaded for grease nipple or automatic lubrication and grease drain hole which is sealed with a metal threaded plug at the factory but can be removed subject to application.
Housings based on ISO 113/II: 1994 and DIN 736: 1984 to DIN 739: 1984.

500 Series for use with tapered bore from 1200K, 2200K, 22200K and 23200K with shaft diameter: 20mm to 140mm. 600 Series for use with tapered bore from 1300K, 3200K, 21300K and 22300K with shaft diameter: 20mm to 90mm.