Optibelt Timing Belts

Optibelt?s Omega timing belts give long lasting
high performance with a number of advantages:
Reduced noise.
Runs in both standard HTD and RPP pulleys.
High efficiency - up to 98%.
Maintenance-free.

Omega High Quality Timing Belts

Super X-Power V-Belt

Moulded Cogged Raw Edge Wedge Belts



Belt Section 10/Z (SPZ/10)

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Optibelt Timing Belts

Optibelt?s Alpha timing belts are manufactured from high grade polyurethane with steel reinforcing cords.

High precision profile for good repeatability.
Very low stretch.
Resistant to many oils and chemicals.
Wide and flexible range.

Alpha Polyurethane Timing Belts

AT-Pitch Range - AT5, AT10

V-Grooved Pulleys for Taper Bushes

Grooves to ISO/BS/DIN 2211.

Belt Section 13/A (SPA/13)

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.

Super X-Power V-Belt

Moulded Cogged Raw Edge Wedge Belts



Belt Section 17/B (SPB/17)

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 22/C (SPC/22)