Sherwood 2 Flute Ball Nose Slot Drills Threaded Shank HSS

Used for diesinking, slot milling and profile milling. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series Type B210T - Inch

SwissTech 4 & 6 Flute End Mills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B.
Shank cutting diameter:
3-6mm to plus0.04 -0.0.
8-20mm to plus0.05 -0.0.

Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 10 Long EML-4WL TiALN Coated

Dimensions to DIN 844.

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Short Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% - Metric

OSG Endmills Carbide

OSG WX-EBD series ball nose endmills have a long plain shank and an extended neck for hardened material. High performance micro grain carbide with Ultra WX coating (multi layered composite TiALN).

For use on material up to 50HRC.
For ultra high-speed machine centres.
For deep slotting. Cutting length: 0.8 x D.

The Ultra WX coating has been developed to improve performance in a wide range of materials including nonferrous materials, mild steels, and refined steels This stable performance remains consistent in both wet and dry applications and is intended for a wide range of cutting conditions, from low speed/reduced cutting force applications to high speed/high cutting force applications.

For all technical and dimensional specifications please refer to our catalogue.

WX-EBD Series 2 Flute Ball Nose Endmill Plain Long Shank Carbide

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Short Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% - Inch

SwissTech 4 Flute End Mills Plain Shank Q-Coat Carbide

Centre cutting. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 50 4 Flute Short EMT-4PS TiCN Coated

Dimensions to DIN 6535 HA

Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS

Used for profile milling and producing open slots. Bright finish. Flute type : 30° Helix. Manufactured to BS 122 : Part 4 : 1980.

Long Series E430T - Metric

For all dimensional specifications please refer to our catalogue.

SwissTech 3 Flute Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 07 Long SDL-3WL TiALN Coated

Dimensions to DIN 844.

Sherwood 2 Flute Ball Nose Slot Drills Threaded Shank HSS

Used for diesinking, slot milling and profile milling. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Long Series Type B230T - Inch

Sherwood® Knuckle Form Ripper Cutters

Sherwood® 'Rippal' 3 flute ripper cutters have centre cutting as standard and as they are manufactured from HSS-Co 8% they operate at higher speeds and feeds than conventional shank milling cutters, removing more metal per minute. The Sherwood® 'Rippal' cutter's unique geometry ensures a more efficient cutting action and reduced cutting time helps you to reduce costs and increase productivity. Power and workholding rigidity must be checked carefully before use as it is recommended that 'Rippal' cutters are used with consistent power feed rates to eliminate backlash.

Sherwood® 'Rippal' cutters are available polished or unpolished and with a weldon or combination shank.

1930M Series 3 Flute 'Rippal' Ripper Cutters Combination Shank HSS-Co 8%