OSG Endmills Carbide

OSG WX-EDS endmills are manufactured from high performance micro grain carbide with Ultra WX coating (multi layered composite TiALN).

For high speed milling in a wide range of applications.
Stub length centre cutting with sharp corner edge.

The Ultra WX coating has been developed to improve performance in a wide range of materials including nonferrous materials, mild steels, and refined steels This stable performance remains consistent in both wet and dry applications and is intended for a wide range of cutting conditions, from low speed/reduced cutting force applications to high speed/high cutting force applications.

For all technical and dimensional specifications please refer to our catalogue.

WX-EDS Series 2 Flute Endmill Plain Shank Carbide

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Long Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% - Inch

SwissTech 3 Flute 37 Coarse Pitch High Helix Roughing Endmills for Aluminium HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 20 Regular RHH-3WR HSS-Co 8%

Dimensions to DIN 844.

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Short Series - Inch

Swiss+Tech 2 Flute Slot Drills Threaded Shank HSS-Co 8%

Centre cutting. Threaded shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 29 Regular SDN-2TR TiCN Coated

Dimensions to DIN 844.

Kennedy® 4 Flute Double-Ended End Mills Plain Shank Solid Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting. Manufactured to ANSI Standards.

For all technical and dimensional specifications please refer to our catalogue.

Regular Series 4 Flute Double End - Inch

SwissTech 4 & 6 Flute End Mills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B.
Shank cutting diameter:
3-6mm to plus0.04 -0.0.
8-20mm to plus0.05 -0.0.

Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 10 Long EMN-4WL TiCN Coated

Dimensions to DIN 844.

Swisstech Fine Pitch Ripper Cutters Weldon Shank HSS-E PM TiALN Coated

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to js12. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 26 Long RFL-4WL HSS-Co 8%

Dimensions to DIN 844.

Sherwood® Knuckle Form Ripper Cutters

Sherwood® 'Rippal' 3 flute ripper cutters have centre cutting as standard and as they are manufactured from HSS-Co 8% they operate at higher speeds and feeds than conventional shank milling cutters, removing more metal per minute. The Sherwood® 'Rippal' cutter's unique geometry ensures a more efficient cutting action and reduced cutting time helps you to reduce costs and increase productivity. Power and workholding rigidity must be checked carefully before use as it is recommended that 'Rippal' cutters are used with consistent power feed rates to eliminate backlash.

Sherwood® 'Rippal' cutters are available polished or unpolished and with a weldon or combination shank.

930MP Series 3 Flute 'Rippal' Ripper Cutters Weldon Shank HSS-Co 8%

The 930MP 'Rippal' cutters have polished flutes making suitable for use when cutting aluminium to ensure optimum swarf removal.

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Short Series - Metric