Starrett Holesaws

The Starrett arbor extension allow holesaws to be used in areas of restricted access.

300mm (12") Arbor Extension

A5 extension fits A2, A17-12 and XA2 arbors.

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Starrett Holesaws

Starrett diamond grit holesaws have a diamond coated cutting edge that is permanently bonded to a tough steel body, which provides the necessary clearance for cutting at high speeds. They will rapidly cut through reinforced plastic, germanium and other abrasives that may not be possible to cut with carbide holesaws.

Holesaw and Arbor sizes:
14-30mm - use Arbor XA1.
32-210mm - use Arbor XA2.

Holesaws Diamond Grit

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Starrett Bi-Metal Holesaws Constant Pitch HSS

Bi-Metal Constant Pitch Holesaws have 6 teeth per 25mm/inch with an aggressive cutting action, featuring a HSS cutting edge welded to a tough alloy steel body. The Constant Pitch provides a smooth cut on thinner gauge materials, with minimal tendency to bite or snag on contact with irregular surfaces. Cutting depth 41mm (1 5/8").

Holesaw and Arbor sizes:
14-25mm - use Arbor A4 or K4.
30-210mm - use Arbor A10 or K10.

Constant Pitch Bi-Metal HSS Holesaws

Starrett Bi-Metal Holesaws Constant Pitch HSS

Bi-Metal Constant Pitch Holesaws have 6 teeth per 25mm/inch with an aggressive cutting action, featuring a HSS cutting edge welded to a tough alloy steel body. The Constant Pitch provides a smooth cut on thinner gauge materials, with minimal tendency to bite or snag on contact with irregular surfaces. Cutting depth 41mm (1 5/8").

Holesaw and Arbor sizes:
14-25mm - use Arbor A4 or K4.
30-210mm - use Arbor A10 or K10.

Constant Pitch Bi-Metal HSS Holesaws

Kennedy Holesaws

Kennedy holesaw arbors are manufactured from alloy steel that is precision machined and threaded, to guarantee a smooth secure fit to all Kennedy variable, constant pitch or carbide tipped holesaws* and are designed to ensure that you can quickly change the hole saw or HSS pilot drill.

Available with hexagon, round and SDS-plus shanks suitable for use with all power tools and are also compatible with all other popular threaded bore hole saws.

For the full range of Kennedy holesaws and arbors please refer to our catalogue.

*When used with the correct size of holesaw.

SDS-Plus 33-152mm Holesaw Arbor (pilot supplied separately)

Starrett Holesaws

Starrett carbide tipped holesaws have a high-hardness and increased resistance to wear this and a triple chip tooth grind, make them ideal for use on PVC, wood, fibreglass, ABS and materials that are too hard and abrasive for regular steel hole saws. The cutting depth is 41mm (1.5/8 inch). The saws have constant 3-pitch teeth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Constant Pitch Carbide Tipped

Kennedy Holesaws Constant Pitch Bi-Metal HSS

Featuring a constant pitch - first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable.

6 teeth per inch.
38mm (1,1/2") cutting depth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

For the complete range of Holesaws and Arbors, please refer to our catalogue.

Starrett Holesaws

Starrett diamond grit holesaws have a diamond coated cutting edge that is permanently bonded to a tough steel body, which provides the necessary clearance for cutting at high speeds. They will rapidly cut through reinforced plastic, germanium and other abrasives that may not be possible to cut with carbide holesaws.

Holesaw and Arbor sizes:
14-30mm - use Arbor XA1.
32-210mm - use Arbor XA2.

Holesaws Diamond Grit