Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Starrett Holesaws

Starrett carbide tipped holesaws have a high-hardness and increased resistance to wear this and a triple chip tooth grind, make them ideal for use on PVC, wood, fibreglass, ABS and materials that are too hard and abrasive for regular steel hole saws. The cutting depth is 41mm (1.5/8 inch). The saws have constant 3-pitch teeth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Constant Pitch Carbide Tipped

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Starrett ?Fast-Cut? Multi-Purpose Hole Saws

Carbide tipped fast cutting multi-purpose holesaws suitable for most construction materials including timber, MDF, blueboard, villa board, hardiplank, plastics, fibreglass etc. 54mm depth of cut allowing easy slug removal. 44 sizes available from 19 to 159mm. Suitable for use in mains and battery powered tools.

Starrett Holesaws

Starrett diamond grit holesaws have a diamond coated cutting edge that is permanently bonded to a tough steel body, which provides the necessary clearance for cutting at high speeds. They will rapidly cut through reinforced plastic, germanium and other abrasives that may not be possible to cut with carbide holesaws.

Holesaw and Arbor sizes:
14-30mm - use Arbor XA1.
32-210mm - use Arbor XA2.

Holesaws Diamond Grit

Kennedy Holesaws

Kennedy holesaw pilot drills are for use with Kennedy holesaw arbors they are manufactured from high speed steel and have ground flutes. Using a pilot drill with a holesaw and arbor ensures the hole is accurately cut exactly where you require it.

For the full range of Kennedy hole saws and arbors please refer to our catalogue.

K14D Pilot Drill for K4 Arbors

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.