Rexroth Blanking Caps

Series QR1-RCA
Metric push-in fitting for compressed air hoses. The user-friendly oval release ring allow the push-in fittings to quickly release from the tubing - much easier than traditional round release rings.
R412005112: diameter 6mm.
R412005113: diameter 8mm.
R412005114: diameter 10mm.

Series S6520

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).



Male Stud Swivel Elbow

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Tap Connectors

Only requires simple hand tightening for connection to terminal taps.

SMC Check Exhaust Valves

Option of built-in silencer or facility to pipe exhaust away.
Accepts nylon and polyurethane tubing. Complete with push-in fittings.

AQ240F-04-00
Applicable tubing diameter: 4mm.
Effective area: in/out 1.7, out/exhaust 2.5.

AQ240F-06-00
Applicable tubing diameter: 6mm.
Effective area: in/out 2.4, out/exhaust 2.7.

AQ340F-06-00
Applicable tubing diameter: 6mm.
Effective area: in/out 4.0, out/exhaust 4.0.

Camozzi Series 2
Mechanically Operated Console Minivalves

Part Number: 235-955
Ports: 10-32 UNF

Technical Specifications:
Valve group 3-way/2-position
Construction Poppet type
Mounting On consoles
Material Anodized body, Brass poppet gate, Buna-N seals, nickel-plated brass plungers
Threaded port sizes M5 (10-32 UNF) thread, or 4 mm O.D. cartridge (5/32" O.D. tube connect)
Installation Bulkhead, or single panel mount
Operating temperature 32°F - 175°F, (dry air necessary down to -4°F)
Fluid Filtered air (25 micron or less recommended)
Lubricant Not required; otherwise, only oil compatible with Buna-N, (3° - 10° E), (ISOVG 32 grade; 32 centistrokes)

Pneumatic Data:
Operating pressure 2 - 10 bar (30 - 145 psi)
Nominal pressure 6 bar (87 psi)
Nominal flow *Qn = 60 NL/min. (2.12 SCFM)
Nominal diameter 2.5 mm
Cv Rating 0.06

Roller Lever Valve

Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Water Trap Tee

Removes moisture from the air line with minimum head loss. An alternative for "swan necks"

Series 2520

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Male - Female Reducers

SMC One-Touch Male Elbow Connectors

KQL
Most common style used to pipe from female thread at a right angle. Colour: black.
KQL04-01S: Tube O.D. 4mm. Thread: R1/8.
KQL04-M5: Tube O.D. 4mm. Thread: M5 x 0.8.
KQL06-01S: Tube O.D. 6mm. Thread: R1/8.
KQL06-02S: Tube O.D. 6mm. Thread: R1/4.
KQL08-02S: Tube O.D. 8mm. Thread: R1/4.

SMC One-Touch Plug-In Reducer

KQ2R
One-touch plug-in reducer.
For connecting to smaller one-touch fittings.

KQ2R04-06 Tube O.D. 4mm x fit dia 6mm.
KQ2R04-08 Tube O.D. 4mm x fit dia 8mm.
KQ2R04-10 Tube O.D. 4mm x fit dia 10mm.
KQ2R06-04 Tube O.D. 6mm x fit dia 4mm.
KQ2R06-08 Tube O.D. 6mm x fit dia 8mm.
KQ2R06-10 Tube O.D. 6mm x fit dia 10mm.
KQ2R06-12 Tube O.D. 6mm x fit dia 12mm.
KQ2R08-10 Tube O.D. 8mm x fit dia 10mm.
KQ2R08-12 Tube O.D. 8mm x fit dia 12mm.
KQ2R10-12 Tube O.D. 10mm x fit dia 12mm.



Colour: white.

Auto-Switches

Auto Switches