Hydraulic Puller/Separator Set

10 ton capacity hydraulic ram with tommy bar. Suitable for agricultural machines, garage and industrial use.



Contents: 1 x hydraulic ram. 3 x 4", 6" & 8" puller legs. 1 x twin head. 1 x triple head. 1 x 50mm ram extension. 1 x 100mm ram extension. 2 x 200mm main rods. 2 x 230mm extension rods. 1 x 75 - 105mm separator. 1 x bolt. 1 x ram ring. 1 x ram nut. Blow moulded storage case

Spare Jaw

Spare Jaws to suit Kennedy Mechanical Pullers. Supplied individually.

Slide Hammer Set

Fully chromed carbon steel slide hammer.



Fully hardened & chromed carbon steel slide hammer with a 1.2kg weight. Slide hammer design for removing bearings from blind housings. Suitable for use where a shaft or other solid surface is not available for a thrust bolt or hydraulic ram to push against. The bearing is removed by the impact action of the slide hammer weight hitting the stop at the end of the bar. The puller legs are securely located on the bearing by screwing down the tapered nut to lock the arms in position. Blow moulded storage case.Functions:2 Jaw internal or external puller. 3 jaw internal or external puller.Hub puller.Dent puller.Lip or edge puller.Grip Wrench Puller.

Bearing Separators

For removing bearings, gears and bushes from shafts where access with a mechanical puller is restricted. Separators have tapered edge for insertion behind close fitting bearings, gears and bushes. Jaw hardness 42- 45 HRC.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

6 Way Hydraulic Puller Set

10 ton capacity hydraulic ram with tommy bar. Supplied with 3 position puller legs covering a spread of 50 - 250mm and reach of 0 - 250mm. Can be used as a 2 or 3 legged puller with the same head.



Contents: 1 x combination head. 1 x hydraulic ram. 3 x 3 position puller legs. 6 x leg connectors. 6 x screw nuts, bolts & washers. 1 x 32mm ext. rod. 1 x ram nut. 1 x blow moulded storage case.

Hydraulic Separator Set

For removing bearings, gears, sprockets & bushes. 10 ton capacity hydraulic ram with tommy bar. Metal storage case.

HS7 105-150mm & HS11 75-105mm

Both sets contain: 1 x hydraulic ram. 1 x separator. 2 x 200mm main rods. 2 x 230mm extension rods. 1 x beam. 1 x ram nut. HS7 (only) also contains 1x 80mm push plate 1x 50mm ram extension. 1x 100mm ram extension.

Bearing Separators

For removing bearings, gears and bushes from shafts where access with a mechanical puller is restricted. Separators have tapered edge for insertion behind close fitting bearings, gears and bushes. Jaw hardness 42- 45 HRC.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Mechanical Separator Set

For removing bearings, gears, sprockets & bushes. Metal storage case.

30 - 75mm

Contents: 1 x 7" thrust bolt. 1 x 30-50mm separator. 1 x 50-75mm separator. 2 x 80 & 100mm main rods. 2 x 90 & 110mm. extension rods. 1 x beam.