Hydraulic Separator Set

For removing bearings, gears, sprockets & bushes. 10 ton capacity hydraulic ram with tommy bar. Metal storage case.

HS7 105-150mm & HS11 75-105mm

Both sets contain: 1 x hydraulic ram. 1 x separator. 2 x 200mm main rods. 2 x 230mm extension rods. 1 x beam. 1 x ram nut. HS7 (only) also contains 1x 80mm push plate 1x 50mm ram extension. 1x 100mm ram extension.

Mechanical Puller Set

Suitable for GM, Ford and Chrysler vehicles. Also suitable for removing pulleys and fly wheels.

SWP9 Steering Wheel

Contents: 1 x yoke, 1 x thrust bolt. 1 x thrust cap. 2 x 75mm screws (5/16" x 24 UNF). 2 x 75mm screws (3/8" x 16 UNC). 2 x 90mm screws (5/16" x 18 UNC). 1 x plastic storage tray.

Mechanical Separator Set

For removing bearings, gears, sprockets & bushes. Metal storage case.

30 - 75mm

Contents: 1 x 7" thrust bolt. 1 x 30-50mm separator. 1 x 50-75mm separator. 2 x 80 & 100mm main rods. 2 x 90 & 110mm. extension rods. 1 x beam.

6 Way Hydraulic Puller Set

10 ton capacity hydraulic ram with tommy bar. Supplied with 3 position puller legs covering a spread of 50 - 250mm and reach of 0 - 250mm. Can be used as a 2 or 3 legged puller with the same head.



Contents: 1 x combination head. 1 x hydraulic ram. 3 x 3 position puller legs. 6 x leg connectors. 6 x screw nuts, bolts & washers. 1 x 32mm ext. rod. 1 x ram nut. 1 x blow moulded storage case.

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

Industrial Reversible/Double Ended Adjustable

Mechanical Puller - 2 & 3 jaw Industrial Kits Reversible/Double Ended/Adjustable

Manufactured from chrome vanadium steel. Each kit contains the components to assemble a 2 or 3 jaw external or internal puller. The legs can be set at 2 different height positions.

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

External Mechanical 2 Long Jaw Puller

Manufactured from drop forged hardened alloy steel. 3 position extra long legs to be used where access is limited. The puller legs are securely located on the bearing by screwing down the tapered nut to lock the arms in position. The legs are then retracted with the bearing by turning the t-bar to extend the thrust bolt on to fixed shaft.
Spread: 10 - 50mm
Reach: 300mm

Kennedy Seal Repair Kit

To suit the Kennedy 10 Ton Hydraulic Ram (KEN-503-7200K). N.B. Hydraulic Ram not included.

Mechanical Puller - 2 & 3 jaw Industrial Kits Reversible/Double Ended/Adjustable

Manufactured from chrome vanadium steel. Each kit contains the components to assemble a 2 or 3 jaw external or internal puller. The legs can be set at 2 different height positions.

Internal & External Puller Set

Fully chromed carbon steel hammer and T-bar for smooth striking action. Supplied in a blow moulded storage carry case.



Fully hardened & chromed carbon steel slide hammer with a 1.2kg weight. Slide hammer design for removing bearings from blind housings. Suitable for use where a shaft or other solid surface is not available for a thrust bolt or hydraulic ram to push against. The bearing is removed by the impact action of the slide hammer weight hitting the stop at the end of the bar. The puller legs are securely located on the bearing by screwing down the tapered nut to lock the arms in position. Blow moulded case.