Dial Indicating Torque Drivers

Can indicate torque in two ways - measures and displays torque as it is applied, or measures and displays the maximum torque used, after it has been applied. Ideal for the electronics, electrical and domestic appliance industries. Stainless steel shafts coloured aluminium handles and scaled nylon dials. 1/4" Hex drive. Dual scale. Manufactured to ISO6789:1992.

Minor Type

Torque Range: 20-100 cNm 28-140 ozf.in

For further specification on this product please see the attached PDF under the catalogue PDF links tab.

16mm Spigot End Fittings

Metric

Open End

Standard Series Torque Multiplier

The 'Standard series' torque multiplier has been designed for the specialist user where it is necessary to provide higher torque than would otherwise be possible due to limitations on space or operator strength. This series employs multiple stage epicyclic gearing to give a wide range of torque outputs and ratios to suit most applications. The torque multiplication is accurate to more than plus/minus 4% with a maximum output of 47,500Nm. *Models contain the AWUR 'anti wind up ratchet' mechanism. As with any high ratio gearbox (25:1 or more) a certain amount of wind-up (spring) has to be taken up before any useful tightening work can be applied to the nut. Each time the input device is released, the wind-up will rotate back against the direction of operation.The AWUR mechanism retains all of the wind up forces as they are created locking the multiplier onto the nut being tightened. This means that even when used upside down the multiplier will support it's own weight.



Torque Range: 3400Nm 2500 Ibf.ft
Square Drive: 1/2?? Input 1?? Output

For further specification on this product please see the attached PDF under the catalogue PDF links tab.

16mm Spigot End Fittings

Metric

Flare End

3/4" Square Drive Industrial Adjustable Ratchet

All Norbar torque wrenches are designed and manufactured to exceed the following national and international standards: BS6703: 1988, ISO 6789: 1992 & U.S.A.GGG-W-00686-C (GSA-FSS)



Robust construction gives accurate results to +/-4%. Back break action indicates when specified torque has been achieved and improves accuracy by reducing the possibility of over tightening. With calibration certificate fully traceable and suitable for ISO 9000 assessment purposes. With ratchet.

Torque Range: 700-1500Nm 500-1000ibf.ft

For further specification on this product please see the attached PDF under the additional information tab.

3/4" Square Drive Industrial Adjustable Ratchet

All Norbar torque wrenches are designed and manufactured to exceed the following national and international standards: BS6703: 1988, ISO 6789: 1992 & U.S.A.GGG-W-00686-C (GSA-FSS)



Torque Range: 150-700Nm 100-500ibf.ft

For further specification on this product please see the attached PDF under the additional information tab.

22mm Spigot End Fittings

Metric

Open End

Kennedy Torque Wrenches

Kennedy 3/8?? square drive fixed head torque wrenches have a high quality chrome plated, polished steel head and retractable torque setting lever. A CLICK & SNAP? action indicates when the pre-set torque level has been reached.

Four easy read scales N.m, kgf.m, lbf.in x10, lbf.ft. Push through square drive connector to instantly reverse action. Knurled grip plastic handle.

Complete with factory tested calibration certificate, operating instructions and torque conversion chart. Supplied in blow moulded cases, except FTW800, which is in a cardboard case.

Manufactured to ISO 6789: 1992 (BS EN 26789: 1994).
Accuracy: plus/minus 4%.

3/8?? Square Drive Fixed Head Torque Wrenches

16mm Spigot

Blank End Fittings.

Norbar Torque Wrenches

All Norbar torque wrenches are designed and manufactured to exceed the following national and international standards: BS6703: 1988, ISO 6789: 1992 & U.S.A.GGG-W-00686-C (GSA-FSS).

1/2" Square Drive Professional Adjustable

Incorporates 'click' sound and 'snap' feel to indicate when torque setting has been reached. Sliding switch on the ratchet head for instant direction reversal (except model 300 and 330, which has a push through square drive). Setting lock to prevent accidental adjustment of the torque setting. Scale located within handle Nm/lbf.ft graduated (kgf.m or ibf.in scale also available, supplied to order). Accuracy to 3%. Supplied in sturdy blow moulded box for protection. Supplied with a traceable calibration certificate to satisfy the requirements of ISO 9000 quality systems. With ratchet.

Torque Range: 8-60Nm 5-45ibf.ft

For further specification on this product please see the attached PDF under the additional information tab.