Dijet Inserts

Grade JC5040
(P20-P40/M15-M40 Coated grade. For die-mould applications across the range of steels and some stainless steels).

For all dimensional and technical specifications please refer to our catalogue.

Peripheral Inserts (P15-P35 M15-M40)

For milling in a variety of steels including tool steels, ferritic and martensitic stainless steels.

RDHX Inserts

Grade JC3552
(P25/K25) TiN PVD Coated Universal grade for steel and cast iron applications. Excellent wear resistance and toughness characteristics. Medium to finish machining.



To suit Dijet Diemaster End & Face Mills

CNMG

QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.

Sandvik CoroKey Indexable Turning Inserts

Sandvik CoroKey GC4225 grade description:
(GC4225 ISO P25 (P10-P35) M15 (M05-M20) CVD Coated. A high performing all round grade. For medium to light roughing applications in Steel.

TCMT Turning Insert

Sandvik CoroKey chipbreaker description: UR - Positive inserts - For rough turning. Broad chipbreaking area in steel, stainless steel, cast-iron and HRSA.

Mitsubishi GY Series Parting & Grooving Holders & Blades

The Mitsubishi GY series of grooving and parting off toolholders are a range of tools designed to offer ultimate rigidity and accuracy for stable grooving applications.

The modular system allows flexible tool selection while maintaining overall strength for stable machining. Additionally, a wide variety of inserts makes it possible to cover a diverse range of machining applications, ensuring high efficiency, high precision machining.

GY Series 90 Internal Grooving Left Hand Modular Holder

For producing 3.00mm Groove width.

CNMG Indexable Turning Inserts

NS530/NS540 (ISO P05-P20) A finishing grade for steel and stainless steel. Gives a superior and consistent surface finish.

Mitsubishi Indexable Milling Inserts

Grade Description: VP15TF (P15-P35/M15-M35/ K15-K30) PVD Miracle Coated Milling/Drilling Grade. Offers increased heat resistance and adhesion strength. For all Steels, Cast Irons and some Stainless Steel

SEMT Indexable Milling Inserts

Chipbreaker: JM - Light to Semi-heavy cutting Breaker.
High accuracy moulded type inserts. Applicable for various workpieces and cutting conditions.
1. General cutting.

Mitsubishi Indexable Milling Inserts

Grade Description: VP15TF (P15-P35/M15-M35/ K15-K30) PVD Miracle Coated Milling/Drilling Grade. Offers increased heat resistance and adhesion strength. For all Steels, Cast Irons and some Stainless Steel

SOMT Indexable Milling Insert

Chipbreaker: JH - Medium to Heavy cutting Breaker High accuracy molded type inserts. Strengthening of the cutter edge prevents chipping and thus fracturing.
1. Interrupted cutting.
2. Scaling.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG N-J Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
(P15-P30/M20-M30/K20-K40/ S15-S25/N15-N25/H20-H30) SUMO TEC TiAlN PVD coated. A tough submicron substrate. For machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds. Excellent notch wear and built-up edge resistance.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG R/L-J/JS Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC830 Grade Description:
(P20-P50/M20-M40/K15-K40/ S15-S40) PVD TiAlN coated tough grade followed by a special SUMO TEC surface treatment. Suitable for milling stainless steel, high temperature alloys and other alloy steels. Recommended for interrupted cut and heavy operations.