产品 / 切削工具 / 数控刀片
编号：SNK1208272H
●产品描述：
VBMT
Suitable for External Toolholders.
编号：YML1201263E
●产品描述：
DCGT
QX530 (ISO P20-P40 M20-M30) Coated. Turning grade for Steels, Cast Steels and Stainless Steels. A good general purpose Steel grade for roughing.
编号：YML1207145G
●产品描述：
TCMT
QX5020 (ISO P10-P35 M10-M30 K10-K30) CVD Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.
编号：SNK1208214R
●产品描述：
VBMT
Suitable for External Toolholders.
编号：ISC1316821A
●产品描述：
ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method
TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.
The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.
Tang-Grip? TAG R/L-J/JS Parting & Grooving Inserts
First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.
IC808 Grade Description:
A tough submicron substrate improved TiAIN PVD coated grade for better chip flow. Designed for machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds, interrupted cut and unfavourable conditions. Excellent notch wear and built-up edge resistance.
编号：SUM1209767B
●产品描述：
AC3000 Carbide Grade (P20 - P40, M20 - M40)
Al2O3 Coated Grade
Designed for interrupted cuts of steels and stainless.
NGU Chipbreaker
Application: medium materials.
编号：MTS1262856L
●产品描述：
Mitsubishi Grooving & Parting Inserts
Grade Description: VP10RT is the first recommendation for turning difficult-to-cut materials with a good balance of wear and fracture resistance.
GY Series Grooving & Parting Inserts
GY Inserts To Suit External Face and Internal Grooving Holders.
A full range of insert widths from 2mm to 6.35mm are available on request.
编号：YML1201071N
●产品描述：
DCGT Indexable Turning Inserts
K10 (ISO K10) Uncoated. Used in combination with a high rake geometry for machining Aluminiums, Plastics and other soft Non-Ferrous materials.
编号：SNK1208270A
●产品描述：
VBMT
Suitable for External Toolholders.
编号：ISC1316961W
●产品描述：
ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method
TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.
The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.
Tang-Grip? TAG R/L-J/JS Parting & Grooving Inserts
First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.
IC808 Grade Description:
A tough submicron substrate improved TiAIN PVD coated grade for better chip flow. Designed for machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds, interrupted cut and unfavourable conditions. Excellent notch wear and built-up edge resistance.