WNMA

QX505 (ISO K05-K15) Coated. Used for finishing, semi finishing and medium roughing of Cast Irons including Malleable and Nodular Irons, at high speed.

Mitsubishi Grooving & Parting Inserts

Grade Description: VP20RT A combination with a tough Miracle coated grade VP20RT makes it suitable for applications where inserts are vulnerable to fracturing.

GY Series Grooving & Parting Inserts

GY Inserts To Suit External Face and Internal Grooving Holders.

A full range of insert widths from 2mm to 6.35mm are available on request.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG N-J Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
(P15-P30/M20-M30/K20-K40/ S15-S25/N15-N25/H20-H30) SUMO TEC TiAlN PVD coated. A tough submicron substrate. For machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds. Excellent notch wear and built-up edge resistance.

AC3000 Carbide Grade (P20 - P40, M20 - M40)

Al2O3 Coated Grade
Designed for interrupted cuts of steels and stainless.

NUP Chipbreaker

Application: optimised machining.

Iscar Turning Inserts

IC9250 Grade description (P20 - P30, M15 - M30).
A TiCN/Al2O3/TIN multi-layer, CVD coated grade. Especially recommended for grooving and turning forged, low carbon and low-alloyed steel parts. Copes efficiently with machining stainless steel at finishing and medium conditions.

TPMR

Sandvik CoroKey Indexable Turning Inserts

Sandvik CoroKey GC1005 grade description:
(HC)- S15 (S10-S25) M15 (M05-M20) PVD Coated. Hard fine grain substrate with good plastic deformation resistance and high wear resistance at high temperatures. Most suitable for Ni, Fe or Co-based heat resistant super alloys.

VBMT Turning Insert

Sandvik CoroKey MM chip breaker description: MM - Positive Inserts Sharp, positive edge and open chip breaker gives low cutting forces and soft cutting action.

DNMG

Suitable for External/Internal Toolholders.

Dijet Inserts

Grade JC5040
(P20-P40/M15-M40 Coated grade. For die-mould applications across the range of steels and some stainless steels).

For all dimensional and technical specifications please refer to our catalogue.

Peripheral Inserts (P15-P35 M15-M40)

For milling in a variety of steels including tool steels, ferritic and martensitic stainless steels.

Mitsubishi Indexable Turning Inserts

Grade Description: NX2525 (P01-15 K01-15)
Cermet. Outstanding grade.
Provides the best in toughness and high wear resistance. has reliability and increased tool life at higher surface speeds in steels and cast irons.

DCMT Indexable Turning Insert

Sandvik CoroKey Indexable Turning Inserts

Sandvik CoroKey GC1005 grade description:
(HC)- S15 (S10-S25) M15 (M05-M20) PVD Coated. Hard fine grain substrate with good plastic deformation resistance and high wear resistance at high temperatures. Most suitable for Ni, Fe or Co-based heat resistant super alloys.

CNMG Turning Insert

Sandvik CoroKey chipbreaker description: QM - Negative insert - Large application area for semi-finishing to light roughing in different materials.