Dronco Diamond Cutting Blades

Dronco Perfect DB blades are the all-round product with a voracious appetite for cutting - for universal use in a broad range of applications on all construction sites or by emergency services. The steel blade is directly coated with diamonds in a special vacuum process.

Fast all-round cutting disc
Innovative vacuum brazed diamond cutting disc
Robust disc for general purpose use on all construction sites

Very good cutting properties in many materials such as:

Concrete, reinforced concrete, exposed aggregate concrete, concrete paving, Indian granite, quarry slabs, granite slabs, sand-lime stone, brick.
Iron constructions and iron profiles, cast iron, sheet metals, non-ferrous metals, ductile pipes.
Plastic, glass, fibreglass, carbon fibre, wood, rubber, etc.

Available in diameters from 115 to 230 mm for use on angle grinders
Diameters 300 and 350 mm for use on petrol-powered cutters and construction site saws.

Perfect DB Diamond Blades

Freud Circular Saw Blades

Anti-kickback Design: Kickback is caused by over-feed. It happens so quickly it can be impossible to react before injury occurs. On a table saw the wood is thrown back violently, on a radial arm saw the blade climbs quickly out of the cut and on a hand held saw the saw is pushed out of the cut. Freud's design reduces this. Each tooth is followed by a limiter, which restricts bite to the maximum safe amount. Teflon Coating. Resistant to friction and heat build-up. Teflon coated blades last longer, cleaning is easy and the distinctive coating also gives rust resistance.Whisper Quiet Expansion Slots: A question-mark shaped slot allows for the necessary expansion yet reduces noise. Laser Cut, High Strength Bodies: The use of precision lasers to avoid unwanted stress in the metal. The method also allows the use of higher strength steel (40 to 45 Rc). These bodies remain true, even after years of use. Tensioned Blades for Superior Flatness: Pre-tensioned blades ensure years of smooth operation. The process is computer controlled and was designed and built by Freud. Advanced Tri-Metal Tip Brazing: Copper alloy is sandwiched between layers of silver alloy (Copper is soft and will stretch without residual stresses, insulating the shoulders from impacts.)

Red Line - Medium

General purpose blades, with medium TPI. For cutting both long grain and cross grain solid wood, giving a good finish.

Kennedy® Flexible Backing Pads

Suitable for use with all portable and air disc sanders. Recommended for use with Kennedy® abrasive discs.

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® Polishing

Wool & Acrylic mix for gentle polishing.

Super Buffing Pads

Air Tool Chisels with 0.401" Shank

For All Brands of Portable Air Chisels including CP, Desoutter, Kobe, Toku and YK.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Cup Brushes Twisted Knot - Threaded Bore

For fast and heavy duty cleaning. The support ring prevents excessive spreading. For removal of rust, paint and scale on large surfaces. 50 SWG