Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® Power Tool Chisels

Suitable for air and electric hammers and breakers, for all classes of work.

Makita Style Chisels

For Makita: HM0810, HR3500, HR3520, 8035NB. 17mm Hex Shank with Round Tang & Round Retainer Recess.

Kennedy® Pin Spanners for Angle Grinders

Several types available. Weight 110g.

Pin Spanner

To suit Bosch, Osaki 115mm, Desoutter 308-354.
Pitch: 30.
Pin diameter: 3.4.

Freud Circular Saw Blades

Anti-kickback Design: Kickback is caused by over-feed. It happens so quickly it can be impossible to react before injury occurs. On a table saw the wood is thrown back violently, on a radial arm saw the blade climbs quickly out of the cut and on a hand held saw the saw is pushed out of the cut. Freud's design reduces this. Each tooth is followed by a limiter, which restricts bite to the maximum safe amount. Teflon Coating. Resistant to friction and heat build-up. Teflon coated blades last longer, cleaning is easy and the distinctive coating also gives rust resistance.Whisper Quiet Expansion Slots: A question-mark shaped slot allows for the necessary expansion yet reduces noise. Laser Cut, High Strength Bodies: The use of precision lasers to avoid unwanted stress in the metal. The method also allows the use of higher strength steel (40 to 45 Rc). These bodies remain true, even after years of use. Tensioned Blades for Superior Flatness: Pre-tensioned blades ensure years of smooth operation. The process is computer controlled and was designed and built by Freud. Advanced Tri-Metal Tip Brazing: Copper alloy is sandwiched between layers of silver alloy (Copper is soft and will stretch without residual stresses, insulating the shoulders from impacts.)

Blue Line - Fine

Cross cut blades, designed with a high TPI. Suitable for cross grain cutting solid wood giving a good finish.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Circular Brushes - Shaft Mounted

Suitable for use in power drills. Most suitable for hard to reach areas and grooves. 6mm Shanks. 30 SWG

Kennedy® Wire Wheels & Brushes

For hard to reach areas such as drilled holes, recesses and corners. For removal of burrs, rust and paint. 30 SWG.
Brush manufactured from Steel wire and holder and shank manufactured from galvanized steel.

Flat End Decarbonising Brushes

Rotabroach SRC Standard Cutters

Rotabroach cutters suit a wide range of applications throughout many industries including construction, engineering, mining, petro-chemical, gas, oil, ship building and railways. Rotabroach cutters are supplied with the industry standard 1/4" pilot bore and can be used in most magnetic drills. 700 N/mm2 material hardness. Fully ground M2 high speed steel cutters.

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits