Kennedy® Router Cutters

Rough Bottom. Used to produce flat bottom panel mould on cabinet and drawer fronts. Can also be used for edge mouldings.

Two Flute Classical Plunging Bits

Kennedy® Pin Spanners for Angle Grinders

Several types available. Weight 110g.

Pin Spanner

To suit Kennedy® M14 pads and 115/125/178mm pads.
Pitch: 35.
Pin diameter: 5.0.

Dronco Diamond Cutting Blades

Dronco Perfect DB blades are the all-round product with a voracious appetite for cutting - for universal use in a broad range of applications on all construction sites or by emergency services. The steel blade is directly coated with diamonds in a special vacuum process.

Fast all-round cutting disc
Innovative vacuum brazed diamond cutting disc
Robust disc for general purpose use on all construction sites

Very good cutting properties in many materials such as:

Concrete, reinforced concrete, exposed aggregate concrete, concrete paving, Indian granite, quarry slabs, granite slabs, sand-lime stone, brick.
Iron constructions and iron profiles, cast iron, sheet metals, non-ferrous metals, ductile pipes.
Plastic, glass, fibreglass, carbon fibre, wood, rubber, etc.

Available in diameters from 115 to 230 mm for use on angle grinders
Diameters 300 and 350 mm for use on petrol-powered cutters and construction site saws.

Perfect DB Diamond Blades

Kennedy® Power Tool Chisels

Suitable for air and electric hammers and breakers, for all classes of work.

Kango Style Chisels

For Kango: 501, 627, 628, 637, 638, 430 - Type 750 Shanks. 19mm Hex Shank with Single Flat and Round Tang.

Freud Circular Saw Blades

Anti-kickback Design: Kickback is caused by over-feed. It happens so quickly it can be impossible to react before injury occurs. On a table saw the wood is thrown back violently, on a radial arm saw the blade climbs quickly out of the cut and on a hand held saw the saw is pushed out of the cut. Freud's design reduces this. Each tooth is followed by a limiter, which restricts bite to the maximum safe amount. Teflon Coating. Resistant to friction and heat build-up. Teflon coated blades last longer, cleaning is easy and the distinctive coating also gives rust resistance.Whisper Quiet Expansion Slots: A question-mark shaped slot allows for the necessary expansion yet reduces noise. Laser Cut, High Strength Bodies: The use of precision lasers to avoid unwanted stress in the metal. The method also allows the use of higher strength steel (40 to 45 Rc). These bodies remain true, even after years of use. Tensioned Blades for Superior Flatness: Pre-tensioned blades ensure years of smooth operation. The process is computer controlled and was designed and built by Freud. Advanced Tri-Metal Tip Brazing: Copper alloy is sandwiched between layers of silver alloy (Copper is soft and will stretch without residual stresses, insulating the shoulders from impacts.)

Red Line - Medium

General purpose blades, with medium TPI. For cutting both long grain and cross grain solid wood, giving a good finish.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® Tie Cord Bonnet Support Pads

High quality 23mm foam pads with rigid back plates. For use with all tie cord bonnets. Bonnets supplied separately. Max 2500rpm. (125mm and 150mm pads are dual purpose - also for use with Velcro bonnets or foams).

Bonnet diameters available: 125mm, 150mm, 180mm, and 200/225mm.
Thread sizes: M14 x 2 and 5/8" UNC.

Kennedy® Router Cutters

Cutter for deep mortising and grooving. Staggered cutting edges give good chip clearance enhancing quality of cut.

Two Flute Staggered Tooth Bits

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Circular Brushes - Shaft Mounted

Suitable for use in power drills. Most suitable for hard to reach areas and grooves. 6mm Shanks. 30 SWG

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.