Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Stem Elbows

Designed to simplify pipe connection in restricted spaces. The Speedfit Stem Elbow provides an instant swivel fitting so pipe can be orientated in any direction. Provides a swivel type connection. Suitable for central heating systems. A special 10mm version gives a neat connection from concealed plumbing to a radiator.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

'Y' Reducer

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Type 2 Conical Silencer Sintered (with Hex)

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

QR1-RPN Series Straight Pneumatic Fitting

Standard metric M5-G 1/2 straight push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.

Series S6520

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).



Male Stud Swivel Elbow

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

3030 Series

Push-Fit Pneumatic Fittings

Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer.
Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: - 0.9 bar min to + 10 bar max.
Temp range: - 20C min to + 70C max.
Tube suitability: nylon, polyurethane.

KQ2H04-01S: Tube O.D. 4mm. R 1/8.
KQ2H04-02S: Tube O.D. 4mm. R 1/4.
KQ2H06-01S: Tube O.D. 4mm. R 1/8.
KQ2H06-02S: Tube O.D. 6mm. R 1/4.
KQ2H06-03S: Tube O.D. 6mm. R 3/8.
KQ2H08-01S: Tube O.D. 8mm. R 1/8.
KQ2H08-02S: Tube O.D. 8mm. R 1/4.
KQ2H08-03S: Tube O.D. 8mm. R 3/8.
KQ2H10-01S: Tube O.D. 10mm. R 1/8.
KQ2H10-02S: Tube O.D. 10mm. R 1/4.
KQ2H10-03S: Tube O.D. 10mm. R 3/8.
KQ2H10-04S: Tube O.D. 10mm. R 1/2.
KQ2H12-02S: Tube O.D. 12mm. R 1/4.
KQ2H12-03S: Tube O.D. 12mm. R 3/8.
KQ2H12-04S: Tube O.D. 12mm. R 1/2.
KQ2H16-03S: Tube O.D. 16mm. R 3/8.
KQ2H16-04S: Tube O.D. 16mm. R 1/2.

Straight Union Connectors

SMC One-Touch Fitting Male Connectors

KQH
Most common style used to pipe from female thread in the same direction.
KQH04-01S: Tube O.D. 4mm. Thread: R1/8.
KQH04-M5: Tube O.D. 4mm. Thread: M5 X 0.8..
KQH08-01S: Tube O.D. 8mm. Thread: R1/8.
KQH08-02S: Tube O.D. 8mm. Thread: R1/4.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Branch Tee to Male Taper

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Equal Tees

Connects plain pipe end to end and at 90.