Protector Sleeves

Contoured high impact resistant plastic grips redirects the force of mishits safely away from your hands preventing injury. Suitable for use with octagonal cold chisels.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Half Round/ Bullnose Chisels

Used for cutting round bottomed grooves in steel such as oil grooves and also for 'roughing up' surfaces to be chipped by a flat chisel. The job is made easier by cutting grooves across the surface with this type of chisel then the raised portion can be easily chipped away with a flat blade.
Cutting angle 40 - 50 degrees to the vertical.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Chisel and V-Notch Wrecking Bars

Multifunctional tools used mainly for prising and levering, drawing large nails and demolition work, ideal for any general dismantling and stripping applications. The versatile Super lever type can be used as a light duty nail lifter, pry bar, adze or lever

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Chisel and V-Notch Wrecking Bars

Multifunctional tools used mainly for prising and levering, drawing large nails and demolition work, ideal for any general dismantling and stripping applications. The versatile Super lever type can be used as a light duty nail lifter, pry bar, adze or lever

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Chisel & Point Crowbar

For heavy duty levering and dismantling work, the angled heel blade offers greater leverage.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Chisel & Point Crowbar

For heavy duty levering and dismantling work, the angled heel blade offers greater leverage.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Diamond Point

Used for squaring out corners in keyways and cutting V shaped grooves in steel.
Cutting angle should be 40 - 50 to the vertical.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Cold Chisel Set (3 Pieces)

Contents:
12 x 150mm
18 x 200mm
25 x 255mm

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.